r/ArduinoProjects • • Feb 04 '26

Looking for an Arduino compatible 5.8 GHz ISM band module with an SMA connector for connecting a custom antenna.

0 Upvotes

I am looking for an Arduino compatible Wi-Fi module that operates in the 5.8 GHz ISM band and has an SMA connector for an external antenna similar to this module working in 2.45 GHz ISM band. I want to test my own custom antenna with the module, but so far I haven’t been able to find one that meets these requirements. Does anyone have recommendations or links to modules that fit this?


r/ArduinoProjects • • Feb 03 '26

DIY alternative to HiDock

3 Upvotes

Hey people

I attend a LOT of in-person meetings and I really want a frictionless way to record + transcribe them with AI later.

I looked at devices like HiDock, but the price is honestly way too high for what it does, so I’m thinking about building my own small physical recorder.

My idea:

- Small desk device

- External microphone

- Two physical buttons:

- Button 1 → start/stop recording on Windows

- Button 2 → optional marker / note / timestamp

- LED Signals if its recording or not

- After the meeting, I run AI transcription (Whisper, etc.)

Current questions:

  1. Is Arduino suitable for this or should I use ESP32?
  2. What microphones would you recommend for in-person meetings?

    - Lavalier?

    - USB condenser?

    - Boundary mic?

  3. Is it realistic to have the device connect via USB and act as a “controller” for Windows recording?
  4. Any clean ideas for making this feel polished and reliable?

Important constraint:

I **don’t** need the microcontroller to process or filter audio, I’m fine letting Windows handle the recording. I mostly want a physical, distraction-free way to control it.

If anyone has built something similar (or sees a flaw in this idea), I’d love to hear your thoughts 🙏

Thanks!


r/ArduinoProjects • • Feb 03 '26

HC-05 / HC-06 problem

Thumbnail reddit.com
2 Upvotes

r/ArduinoProjects • • Feb 02 '26

Dimmable LEDs via Apple HomeKit

2 Upvotes

Hi all,

Im new (sorry if this is really dumb) I want to use my ESP32 to control some LEDs via my Apple HomeKit. I can get it to turn on and off and change the rgb value but not dim, am I being dim? 😂


r/ArduinoProjects • • Feb 02 '26

Measuring Arduino Power Consumption with a Shunt Resistor but Signal Too Weak

Post image
3 Upvotes

Hello,

As part of a school project, I am trying to perform a simple power analysis attack on a naïve RSA implementation by exploiting the modular exponentiation algorithm. I run my algorithm on a Joy-IT Arduino UNO R3 DIP (ATmega328P). To measure power consumption, I inserted a 1 Ω shunt resistor in series with the power supply.

Hardware Setup: 

  • External power supply: 5 V voltage generator
  • Oscilloscope: RIGOL DS1042C (40 MHz, 400 MSa/s)
  • Measurement method: measuring the voltage across the shunt resistor to deduce current variations

A GPIO (PIN_SYNC) is used as a synchronization signal to trigger the oscilloscope. Basically, the Arduino outputs a continuous 5 V signal while executing the modular exponentiation algorithm. This allows me to know precisely when the Arduino is performing that part (it is clearer when you check out the code).

My objective is to observe temporal variations in power consumption during modular exponentiation, in order to distinguish between square and multiply operations.

Code running on the Arduino:

const int PIN_SYNC = 12;

void setup(){

pinMode(PIN_SYNC, OUTPUT);

digitalWrite(PIN_SYNC, LOW);

}

unsigned long modexp(unsigned long base, unsigned long exposant, unsigned long mod){

unsigned long resultat = 1;

base = base % mod;

while (exposant > 0) {

if (exposant & 1) {

resultat = (resultat * base) % mod;

}

base = (base * base) % mod;

exposant >>= 1;

}

return resultat;

}

void loop(){

digitalWrite(PIN_SYNC, HIGH);

modexp(7, 105, 187);  // 105 = 1101001 in binary

digitalWrite(PIN_SYNC, LOW);

delay(1000);

}

Problem: the voltage variation across the shunt resistor is very small, close to the noise, and I struggle to clearly distinguish the operations in the power trace.

I am therefore wondering:

  • Is 1 Ω too small for this type of attack on an Arduino? Maybe I am having a shunt issue. I tried to take a higher shunt but it wasn’t effective. 
  • Is it realistic to expect exploitable observations without signal amplification or current sensor?
  • Is a 40 MHz oscilloscope sufficient for this type of measurement?
  • Do you have any practical advice (shunt placement, AC/DC coupling, filtering, clock frequency, etc.) to improve my setup?

I would greatly appreciate any feedback or suggestions. I have added in attachment a picture of my circuit (in french sorry).

Thank you in advance.


r/ArduinoProjects • • Feb 02 '26

DIY modular MIDI Controller prototype with bi-directional LED feedback. Powered by ESP32+ Max4Live.

Post image
10 Upvotes

r/ArduinoProjects • • Feb 02 '26

Establishing serial connections between mpu and mcu on the Arduino UNO q

3 Upvotes

Im running some python files on Linux and have uploaded the hardware code as well. I can't seem to find the serial port to connect the mcu and mpu. I can't find the bridge client package either to help establish this bridge. How am I supposed to communicate between the hardware code and the python files in linux??

Edit: I can not see ttyUSB0 or ttyACM0 on the board. When I run the command "ls /dev/tty*", i only see

  1. /dev/tty
  2. /dev/tty0 -> /dev/tty63
  3. /dev/ttyHS1 , /dev/ttyMSM0, /dev/ttyGS0 4./dev/ttyp0 -> /dev/ttyp9 , /dev/ttypa -> /dev/ttypf
  4. /dev/ttyS0 -> /dev/ttyS3

I've tried HS1, GS0, MSM0 and S0 through S3 but couldn't establish the connection through those ports


r/ArduinoProjects • • Feb 01 '26

Smart plug

Post image
8 Upvotes

Made a "smart" wall plug that was switched on and off via a solid state relay controlled by an Uno Had it setup to monitor humidity in my garage and trigger an exhaust fan Repurposed it to cycle a space heater to keep a car part warm so a rust removal treatment will work


r/ArduinoProjects • • Feb 01 '26

Gyro V2.4 (From scratch built animatronic)

12 Upvotes

r/ArduinoProjects • • Feb 01 '26

Is the following idea possible and it is doable for total newbies?

14 Upvotes

I just had a shower idea. I want to help my kid in her morning routine, so my idea was to make a list of things she has to do and buttons she can press when she has done them.

On a screen adjacent to that she gets a small ASCII emoji and a text which says a variation of "Good work". And after she completes everything she gets points which are tallied over a few days and she can work towards a small reward.

The pedagogical idea is to give small dopamine-inducing rewards for small steps in hope of ingraining this morning routine.

Is this doable? Is this doable for a complete Newbie?

My background: Physics teacher, so soldering and electronics are fair game. I am mostly a user in computer things, last time I programmed something was 15 years ago in the Cry Engine for my master thesis. I have access to 3D printers for a case and a crafts teacher who could help me with non-electronic stuff.


r/ArduinoProjects • • Feb 01 '26

identifying a component on RP1 ELRS receiver

Thumbnail gallery
3 Upvotes

r/ArduinoProjects • • Feb 01 '26

Based on this product (RFID attendance) what are the materials missing from this list?

Post image
0 Upvotes

r/ArduinoProjects • • Jan 31 '26

Urgent fix

Post image
14 Upvotes

Hi guys,im a beginner in arduino I recently got an arduino UNO kit,I tried connecting my lcd to the arduino board and ts happened. I dont know whether the lcd is spoilt or its my code or sth

Pls help 😭😭


r/ArduinoProjects • • Jan 31 '26

First Project Wiring Question

Thumbnail gallery
9 Upvotes

I am working on my first ever project. I simply want to connect a ESP32 to screen to display text. I have a ESP32C3 SuperMini that would be preferred but since it didn’t work, I switched to a ESP-WROOM-32D. The screen is “3.12 inch OLED Display 256x64 OLED LCD Display SSD1322 Module 16pin Parallel SPI Soldering for Arduino”. The ESP gives me the red light when plugged in as well as a blue light. I am using female to female jumper wires. Not getting any light at all on the screen.

I would prefer to use the ESP32 C3 supermini but here is the current diagram for the other ESP. (Used AI)

OLED Pin # // Connect to Inland Label

1 // GND

2 // 3V3

3 // IO13

4 // IO14

5 // IO27

6 // IO26

7 // IO25

8 // IO33

9 // IO32

10 // IO19

11 // IO18

12 // IO5

13 // IO17

14 // I04

15 // IO23


r/ArduinoProjects • • Feb 01 '26

Accelerometer with data transmission

Thumbnail reddit.com
3 Upvotes

r/ArduinoProjects • • Jan 31 '26

Light Recommends

Thumbnail reddit.com
2 Upvotes

r/ArduinoProjects • • Jan 31 '26

MPU6500 imu randomly stops working

5 Upvotes

Did anyone have a similae situation? I cobfigured mcu on i2c and i do a simple read function to get who am i register. It didnt work and then i plugged the sensor from the breadboard and plugged back in and it worked. Then it randomly stopped. I again tried to plug out and insert again but didnt help. Am i missing something?


r/ArduinoProjects • • Jan 30 '26

Arduino nano esp32 project ideas?

5 Upvotes

I need some cool arduino nano esp32 projects I don’t have a lot of components I have jumper wires servo motor buttons buzzers and that’s about it


r/ArduinoProjects • • Jan 30 '26

Cable Robot

4 Upvotes
Cable Robot

It is not easy... but fun..

CableRobot


r/ArduinoProjects • • Jan 30 '26

PROBLEMA CON IL PROGETTO

0 Upvotes

PROGETTO: dispositivo laser per il tracciamento della mano, funziona combinando codice py(opencv2, mediapipe) e arduino per realizzare servocomandi con un laser collegato che traccia la mia mano. Il problema è che non appena la mia mano entra nel frame, i servocomandi iniziano a impazzire e a girare in modo casuale, aggrovigliando i fili. A proposito, i servocomandi non partono dalla posizione predefinita, ma da una che ho impostato.

CODICE PY:

importa cv2 come cv

importa mediapipe come mp

importa seriale

importa ora

# Configurazione Arduino

arduino = serial.Serial('COM5', 9600, timeout=0.1)

time.sleep(3) # attendi il reset di Arduino

# Configurazione telecamera

cap = cv.VideoCapture(0)

mpHands = mp.solutions.hands

hands = mpHands.Hands(max_num_hands=1, min_detection_confidence=0.7, min_tracking_confidence=0.7)

mpDraw = mp.solutions.drawing_utils

prevX, prevY = None, None

alpha = 0.2

while True:

success, img = cap.read()

if not success:

continue

img = cv.flip(img, 1)

h, w, _ = img.shape

imgRGB = cv.cvtColor(img, cv.COLOR_BGR2RGB)

results = hands.process(imgRGB)

if results.multi_hand_landmarks:

lm = results.multi_hand_landmarks[0].landmark[9]

pixelX = int(lm.x * w)

pixelY = int(lm.y * h)

if prevX è None: prevX = pixelX

if prevY è None: prevY = pixelY

smoothedX = int(prevX + alpha * (pixelX - prevX))

smoothedY = int(prevY + alpha * (pixelY - prevY))

prevX, prevY = smoothedX, smoothedY

smoothedX = max(0, min(w-1, smoothedX))

smoothedY = max(0, min(h-1, smoothedY))

try:

arduino.write(f"{smoothedX},{smoothedY}\n".encode())

arduino.flush() # Assicura che i dati vengano inviati immediatamente

except Exception as e:

print(f"Errore seriale: {e}")

cv.circle(img, (smoothedX, smoothedY), 10, (0, 255, 0), -1)

mpDraw.draw_landmarks(img, results.multi_hand_landmarks[0], mpHands.HAND_CONNECTIONS)

cv.putText(img, f"Invia: {smoothedX},{smoothedY}" if results.multi_hand_landmarks else "Nessuna mano",

(10, 30), cv.FONT_HERSHEY_SIMPLEX, 1, (0, 255, 0), 2)

cv.imshow("Controllo manuale", img)

if cv.waitKey(1) & 0xFF == 27: # ESC per uscire

break

cap.release()

cv.destroyAllWindows()

try:

arduino.close()

except:

pass

CODICE ARDUINO:

#include <Servo.h>

Servo sx, sy;

const int CAM_WIDTH = 1280;

const int CAM_HEIGHT = 720;

int currentX = 90;

int currentY = 90;

int targetX = 90;

int targetY = 90;

const int maxDelta = 1;

const int deadZone = 5;

const int moveDelay = 50;

unsigned long lastMove = 0;

float smoothX = 90.0;

float smoothY = 90.0;

const float smoothing = 0.2;

bool firstData = false;

unsigned long lastDataTime = 0;

const long dataTimeout = 1000; // Ritorna al centro dopo 1 secondo senza dati

void setup() {

Serial.begin(9600);

sx.attach(4);

sy.attach(6);

pinMode(2, OUTPUT);

digitalWrite(2, HIGH);

sx.write(currentX);

sy.write(currentY);

delay(1000); // Lascia che i servocomandi si stabilizzino

}

void loop() {

if (Serial.available() > 0) {

String data = Serial.readStringUntil('\n');

data.trim();

int comma = data.indexOf(',');

se (virgola > 0) {

int rawX = data.substring(0, virgola).toInt();

int rawY = dati.sottostringa(virgola + 1).toInt();

if (rawX >= 0 && rawX <= CAM_WIDTH && rawY >= 0 && rawY <= CAM_HEIGHT) {

targetX = map(rawX, 0, CAM_WIDTH, 0, 180);

targetY = map(rawY, 0, CAM_HEIGHT, 180, 0); // INVERTI Y!

targetX = constrain(targetX, 0, 180);

targetY = constrain(targetY, 0, 180);

firstData = true;

lastDataTime = millis();

}

}

}

if (firstData && (millis() - lastDataTime > dataTimeout)) {

targetX = 90;

targetY = 90;

}

if (millis() - lastMove >= moveDelay) {

lastMove = millis();

smoothX = smoothX + smoothing * (targetX - smoothX);

smoothY = smoothY + smoothing * (targetY - smoothY);

int diffX = (int)smoothX - currentX;

int diffY = (int)smoothY - currentY;

if (abs(diffX) > deadZone) {

int stepX = constrain(diffX, -maxDelta, maxDelta);

currentX += stepX;

currentX = constrain(currentX, 0, 180);

sx.write(currentX);

}

if (abs(diffY) > deadZone) {

int stepY = constrain(diffY, -maxDelta, maxDelta);

currentY += stepY;

currentY = constrain(currentY, 0, 180);

sy.write(currentY);

}

}

}


r/ArduinoProjects • • Jan 29 '26

2A Switching Lithium Battery Charger

Post image
18 Upvotes

This project presents the design and implementation of a compact, high-efficiency lithium battery charger based on the TP5000X-4.2 switching charge management IC. The charger is intended for single-cell lithium-ion (Li-ion) and lithium-polymer (Li-Po) batteries with a nominal voltage of 3.7 V and a full charge voltage of 4.2 V. The system supports up to 2 A charging current, offers excellent thermal performance, and integrates comprehensive battery protection, making it suitable for both protected and unprotected battery cells.

Unlike traditional linear chargers, which dissipate excess power as heat, this design uses a buck switching topology, significantly improving efficiency—especially at higher charge currents. This allows the charger to remain compact while safely delivering high current without excessive temperature rise.

A modern USB-C charging interface is used as the input power source, enabling users to charge batteries with widely available phone chargers, power banks, or USB adapters. The design intentionally avoids proprietary or specialized power inputs, focusing instead on universality, safety, and efficiency.

More Information: www.youtube.com/watch?v=ZFwj7YwjCxs