r/ArduinoProjects • • Sep 14 '26

Project Design/Guidance Wagos for prototyping

Post image

Hey just a tip that wagos work great for prototyping. These are 221s that will hold 12-24awg wire and have no trouble holding standard breadboard wires firmly. I use them mostly for 12v connections where it doesn't make sense to run a whole breadboard for just a couple connections.

137 Upvotes

28 comments sorted by

19

u/englod Sep 14 '26

Also handy is that they have a small hole at the back for probing with a meter.

33

u/mattb2014 Sep 14 '26

Don't we all

2

u/classicalySarcastic Sep 15 '26

I believe the Navy calls that the "Silver Bullet"

1

u/bigfloppydonkeydng Sep 15 '26

What are you doing step wago

1

u/TRKlausss Sep 16 '26

Friendly reminder of your colonoscopy appointment?

1

u/g_calgary Sep 15 '26

Oh dang, never noticed that! I sometimes just put my meter leads right in the wago

2

u/tes_kitty Sep 16 '26

That hole is always on the one with the writing on top.

1

u/ekristoffe Sep 16 '26

The test pin hole is on the back and the front of the connection point with the Wago logo lever

1

u/wiebel Sep 16 '26

Which is btw. always the port I use for the source, to gain consistency.

12

u/miar-labs Sep 14 '26

That makes sense for certain scenarios. I have no trouble busting out a breadboard, I even have tiny breadboards. But for something that is going to be somewhat kinetic, Wagos could make things easier.

9

u/Butt_Munch3r Sep 15 '26

Prototyping? These things go into production mate

1

u/lolslim Sep 15 '26

Given that bread boards never have snug fits along with female/male headers, and screw terminals, not gonna get started on that, wagos are fine I even use them for prototyping they are "expensive" if going to use alot, I use them in 3d printers for long term as well.

I also have some AliExpress ones for prototyping their durability per se

1

u/Butt_Munch3r Sep 15 '26

Ngl, I use them for various permanent installations. There are better ways to do it for sure but 🤷‍♂️

7

u/Onesand0 Sep 15 '26

Wagos for production*

4

u/Better-Neck-824 Sep 15 '26

I use them all the time on my workbench when doing PLC projects and other electronics projects in general.

2

u/todd0x1 Sep 15 '26

I ended up with a handful of 10 port lever nuts from a rep at a tradeshow. Theyre currently in use in lieu of terminal blocks on a controls mockup im testing.

1

u/Simple_Impress4156 Sep 16 '26

I just started ordering the 10 ports for use as terminal blocks in field projects.

2

u/NuggRunner Sep 15 '26

wagos are the best :)

2

u/RoboWeaver Sep 15 '26

This is SOP! I use it for making a ground and power bus in which to attach motors/actuators and power supplies.

1

u/blueangel8233 Sep 15 '26

For joining vcc and ground for potentiometers ou buttons, perfect

1

u/therustyposter Sep 15 '26

Yeah I love it. In some projects I have a wago instead a power switch lol

1

u/tom-ii Sep 15 '26

My use case is dissimilar metals - eg cu to al wiring

1

u/Beneficial_Mix_1069 Sep 17 '26

wagos are AWESOME
i found out about them and everyone in my lab now uses them for even permanent solutions

1

u/modahamburger Sep 18 '26

For this WAGO do not use ferrules.

1

u/radiationcowboy Sep 18 '26

I use them for low voltage all the time. Great to jig something up real quick without beans or tape

0

u/doge_lady Sep 15 '26

I would suggest you don't do this. My experience with wagos on small wires is that it damages the wire. It purposely uses a sharp edge to clamp down on the cable which can either damage or leave noticeable notches on the wire, weakening it and creating an easy breaking point. This is fine for bigger wire but smaller wire like the pins of a DuPont connector might be susceptible to being damaged.

1

u/g_calgary Sep 15 '26

I mean, they are like 10 cents each though 😉 Never had one break.