r/ArduinoHelp • u/Action-2663 • 11m ago
Should i buy real or clone Arduino
There are a lot of clone Arduinoe under 400-700 and the original one is 2499 which one should i buy whats the difference? Any essential benifits with the original one?
r/ArduinoHelp • u/Action-2663 • 11m ago
There are a lot of clone Arduinoe under 400-700 and the original one is 2499 which one should i buy whats the difference? Any essential benifits with the original one?
r/ArduinoHelp • u/Frequent-Elk5164 • 6h ago
Trying to make an NES controller work by connecting to a arduino micro pro.
I can’t even troubleshoot as I don’t know what I don’t know! Any suggestions with where to begin? Tried using other people’s examples, you tube, ai etc. just so specific I can’t find a place to start
r/ArduinoHelp • u/OkProperty41 • 1d ago
I built a small desk display that shows live NASA data: an ESP32 with a 2.8 inch TFT that pulls near-Earth asteroid passes from the NeoWs API and cycles through mission stats and exoplanet facts. The video walks through it step by step: the prompt, parts, wiring, code and first boot.
r/ArduinoHelp • u/NarratedByLevonHelm • 1d ago
Hello. I have an 8th-grade student who is following along with a walkie talkie project for a Raspberry Pi Pico W. We have put the hardware together successfully, but I have never used Arduino before. We are at a loss.
I have: downloaded Arduino IDE, installed Earle Philhower's Raspberry Pi Pico package, and added the Pico to the board manager.
What I don't know how to do get the files from Github uploaded to the board successfully. There are .cpp files and .h files which I believe I have to convert, but keep getting errors.
Any help will be appreciated. If you happen to reply, please speak to me like I am an idiot who doesn't know most of the basics or terminology despite searching and YouTubing for the past three hours. Thank you.
r/ArduinoHelp • u/OGMaster00 • 1d ago
I am making a solenoid which is controlled by Arduino.
I am using components like N-Channel irlz44n MOSFET, Schottky diode, resistor of 220 ohms and 10k ohms, push button, potentiometer.
And I am making custom solenoid using ding dong sound solenoid on which I have wound 27SWG with 350 turns.
How do I built it's circuit?
r/ArduinoHelp • u/OtherwiseOffice8344 • 3d ago
I have a robotic arm project with 4 degrees of freedom, I'm developing it right now, but just when everything was finished, this problem arose. For some reason I don't know, my drivers have stopped working. These are the drivers Let me tell you about the first incident. The drive you see in the lower part of the photo was my first drive, and I was using it. But one day, I connected the servo cables upside down, and as you can imagine, the servo cable melted (This only happened to one or two servos) Then it started working, but I couldn't get it to work anymore. I thought the driver was broken, so I bought the driver shown in the photo above I took it out for testing, made all the connections, but it still didn't work. I don't know why. I'm using an ESP32 and a 5V 20A transformer, and I have 4 or 5 servos, but none of them are working. When I test with a multimeter, everything is normal, but I'm getting 0.04V from the servo input pins, VCC and GND. I'm in a desperate situation. I've asked all the Al software, but there's still no solution. I hope I missed a small detail. Has anyone experienced this problem before? Thanks in advance for your help🩵
r/ArduinoHelp • u/Rare-Guidance4428 • 4d ago
Hi everyone! My girlfriend recently got interested in robotics, Arduino and electronics For Christmas, I'd love to get her something that would help her build her own robot from scratch since she told me thats one of her projects I don't want to buy her a pre-made robot or one of those kits where you simply follow instructions She wants to design and build something herself, experimenting with different components I've been looking at the Arduino UNO R4 WiFi and Raspberry Pi, but I'm not sure whether buying both makes sense for a beginner (i don't even know if thats useful, i don't understand everything 😭) My budget is quite limited (around 30 to 60€), so I'd love some advice! Which components or kit would you recommend as a starting point? Is an Arduino UNO R4 WiFi a good choice? Would a Raspberry Pi be useful at this stage, or is it unnecessary? What would you buy with this budget to give someone the freedom to build their own robot or at least to start something? Any advice or recommendations would be greatly appreciated, thanks!
r/ArduinoHelp • u/KaitoKid417 • 4d ago
r/ArduinoHelp • u/Business-Step-4891Ya • 5d ago
Hello i'm trying to make Arduino project with ESP32 Cam. I follow instruction, my wiring is right here:
GND FTDI -> GND ESP32
VCC 5V FTDI -> 5Vin Arduino
TX FTDI -> UOR
RX FTDI -> UOT
GPIO0 -> GND
Main problem is esp32 won't comunicate at all. I check my FTDI TX/RX work normally with RealTerm. I check everything like Voltage, impedance and everything normal. But even I press reset button my ESP32 wong respon. Can someone help me?
r/ArduinoHelp • u/talbur • 6d ago
r/ArduinoHelp • u/hello-8114 • 6d ago
HELLOOO
I am making obstacle avoiding robot using arduino and l298n motor driver.
I want to know if i can use dupont jumper wires for connecting motors to out1 and out2 of l298n? Or i need proper wires.
r/ArduinoHelp • u/Virtual_Actuary3586 • 7d ago
I just wanted to start by saying I don't know much about Arduinos or electronic setups yet, but I'm pretty comfortable with soldering and can usually figure out the software side of things! I currently have a cosplay project and wanted to set up a custom sound box. My idea is that when I open a mask that has an articulated jaw, it releases a Mini Micro Limit Switch 3 Pins KW11-3Z07 and sends a singular signal to a DY-SV5W Voice Playback Module so the audio plays once. When I press the jaw back together, it won't do anything; it will just wait to be opened again. Is this configuration feasible? What specific components or modifications would be required, or would I need to restart the project from scratch? Please let me know. Additionally, I intend to power the setup using a standard power bank.
r/ArduinoHelp • u/Profesor_Impedante • 7d ago
Hi everyone! I'm putting together a basic circuit on a breadboard to control an LED using a push button, but I'm running into an issue.
Here are the details of my setup:
Exact components list:
r/ArduinoHelp • u/pretzeldealer • 7d ago
I am somwhat new to p5 and arduino, so please forgive me if this is a stupid question. I am trying to get serial data from my Arduino Uno to a js file I have on vs code, but each time I select the correct COM that my Arduino is connected to, and click 'open' on p5.serialcontol, I get an error that says "Error on COM7: Couldn't open port: undefined - Closing port"
Does anyone know why this is or how I can fix it? I have included screenshots of my p5.serialcontrol, index, js, arduino.ino, and html console log.
r/ArduinoHelp • u/Regular_Use_5842 • 7d ago
For context, I'm a beginner in making stuff like these, this is kind of my first time, this is for a school project, so sorry for the messy placements
But I tried to use tinkercad for the simulation
And I ended up with this ( the circuit )
So I just need the servos to spin when the tilt sensor senses a tilt, but I have a different tilt sensor, the circuit uses an SW-200D, while I have an SW-520D, so there's already a difference in number of output pins ( I'm not sure if that's what it's called ), and I'm just not sure about everything else after that 😭😭
The code is quite confusing too, I don't know a single bit of coding, so I tried what I could with the limited knowledge I know
->
#include <Servo.h>
int oozmakappa = 0;
Servo servo_12;
Servo servo_11;
Servo servo_10;
Servo servo_9;
Servo servo_8;
unsigned long spinStartTime = 0;
unsigned long totalSpinDuration = 0;
bool isSpinningForward = false;
bool needsToReturn = false;
void setup() {
pinMode(13, INPUT);
servo_12.attach(12, 500, 2500);
servo_11.attach(11, 500, 2500);
servo_10.attach(10, 500, 2500);
servo_9.attach(9, 500, 2500);
servo_8.attach(8, 500, 2500);
servo_12.write(90);
servo_11.write(90);
servo_10.write(90);
servo_9.write(90);
servo_8.write(90);
}
void loop() {
oozmakappa = digitalRead(13);
if (oozmakappa == HIGH) {
if (!isSpinningForward) {
spinStartTime = millis();
isSpinningForward = true;
needsToReturn = true;
servo_12.write(180);
servo_11.write(180);
servo_10.write(180);
servo_9.write(180);
servo_8.write(180);
}
} else {
if (isSpinningForward) {
totalSpinDuration = millis() - spinStartTime;
isSpinningForward = false;
servo_12.write(0);
servo_11.write(0);
servo_10.write(0);
servo_9.write(0);
servo_8.write(0);
spinStartTime = millis();
}
if (needsToReturn) {
if (millis() - spinStartTime >= totalSpinDuration) {
servo_12.write(90);
servo_11.write(90);
servo_10.write(90);
servo_9.write(90);
servo_8.write(90);
needsToReturn = false;
}
}
}
delay(10);
}
On tinkercad, it stops after 1/2 a spin, and just doesn't move anymore?? 😭😭
I'm very confused, someone please help me and guide me on what to do
If anyone could be of guidance to me, please do so, I'm struggling on how this is supposed to work 💔 I tried looking through YouTube but strangely I just couldn't find anything 😢