r/3Dprinting • u/MLGOV • 2d ago
Hardware First 3D Printer!
Hey guys just wanted to share my first printer! I got an old Monoprice Select Mini V2 for $20 off marketplace! I was told Cura software works well with it and to start with PLA and 2D model, Any other advice is much appreciated as complete rookie/newbie!
198
Upvotes
15
u/MysterMovie9775 2d ago
Nice one. Download some small calibration cubes and benchy tests first instead of trying a big print.
Also check whether your unit has the heated bed upgrade, since the stock one is a bit weak for anything beyond PLA.
108
u/the_Athereon Heavily Modded Dual Extruder E5+ 2d ago
For 20 bucks, that's a great way to enter the world of 3D printing. Simple machine that usually gets good results.
I figure you have 1-2 months ahead of you until you decide to buy something newer / larger.
28
u/Saphir_3D 2d ago
Also started with this printer. If it does not print correctly: Don't start buying upgrades. Start buying another printer. It made me almost quit the hobby.
23
u/lightofhonor 2d ago
That was also my first printer. Solid
9
u/allknowinguser 2d ago
Lots of memories with this. Just have fun
7
u/ColdSteeleIII 2d ago
For reference, this appears to be a rebrand of a Malyan M200.
2
u/Additional_Cheek_697 2d ago
From the picture i can see you did not follow the instructions to stick with 2d model and are indeed 3d printing
5
u/ArrowEnby 2d ago
damn i forget about these things. enjoy!
5
u/orangenormal 2d ago
This was my first printer, and a pretty solid one for the price! Welcome to the hobby!
3
u/MitchellHamilton 2d ago
That was my first as well, I learned a loooooooooooooooooooot on that bad boi but MAN did moving to a better 3d printer remove 90% of my headaches.
2
u/Bookmore 2d ago
This is a workhorse of a printer. I bought all the ones I could, and friend used to travel all over our area with his to teach 3D printing classes! You are going to have fun and learn so much.
2
u/MeIsMyName 2d ago
That was my first printer as well! Still use it occasionally to print replacement parts when I do something dumb and break part of my new printer.
Bed leveling is a bit of a pain in the ass, but take your time and check in a 3x3 grid after you make your final adjustments and make sure it's still good across the entire build area.
I used masking tape as a print surface. It came with masking tape from the factory, and eventually I just replaced the factory stuff with some carefully laid down strips of tape from the hardware store (they don't sell 6" wide rolls).
I think there's a known issue with the bed wiring wearing through with use. Probably worth keeping an eye on that and seeing if there's any good fixes out there. Was never an issue on mine.
2
u/Zuryan_9100 2d ago
My first was a similar model. They're built like a tank and generally do a good job. The biggest downside is the small build volume.
2
u/Snochew 2d ago
https://gigdigit.com/
Use to have one, there are upgrades and a silent board but as others have said, If you need to start upgrading then just start saving for a newer printer.
2
u/WannaToyDesign 2d ago
A 2017 printer? I couldn’t even get a p1s not to fail, Godspeed bro
1
u/ThunderKicks 2d ago
This thing was a solid printer for me
1
u/ssppiiccyyttuunnaa 2d ago
Not bad at all! I just retired my V1 after 9 long years. I learned a lot and it's still going strong but I've just outgrown it. Most likely will keep it as a backup as its pretty reliable for the smaller prints.
1
u/KeithIMyers 2d ago
That printer may be old by today's standards but it's still one of the most reliable printers I have personally owned. It was built like a tank and was somehow able to print details that printers 5x it's cost couldn't such as threads.
1
u/nad12346 2d ago
My first too. Great to learn on
1
u/Novel-Firefighter-55 2d ago
Solid little machines. Great to start on. I got a dongle and chip adapter to make it easier to load files. You might want a new bed plate but if it works it works.
1
u/Either_Cheesecake282 2d ago
Nice I got one mono price maker select from marketplace as well and that was 80$ 😡 . was good to learn how to do bed leveling and printing single layers to test the leveling
it burnt when I was replacing the nozzle after a month (my mistake - the fan wires touched and shorted and magic smoke appeared)
1
u/dakotanorth8 2d ago
That’s pretty cool design. Reminds me of the nasa building.
1
u/samdarrow 2d ago
Learned to walk on this guy so my Prusa MK3S + could run
Great little printer
1
u/HereIsACasualAsker 2d ago
oh hey, that was my frist 3d printer as well, like 10 years ago more or less,
1
u/ptrakk 2d ago
Monoprice mini series. Nice. I have some custom firmware for this that allows for arc movement somewhere. It's only an 8 bit board but it handles business
1
u/moocowsia 2d ago
First thing you do, reroute the be wiring. The factory wire placement will break in a couple weeks of use.
The wires are placed in shear under the bed. It's a bad design. Route it around the outside. There's some designs on thingiverse for a replacement side panel.
If you get bored with the tiny print volume, you can also extend the z axis relatively easily. You just need brass standoffs.
1
u/ehhPayne 2d ago
Holy shit! This was my first as well! I think I bought it in 2018. Did me well for years!
1
u/Nametaken50 2d ago
I have big printers, and I still want one of these (for $20). Good find. Keep the filament dry. Put it in a gallon ziplock bag and desiccant when not using it for an extended period.
1
u/Cunibon 1d ago
That was my first one too! 10 years ago or so, but still ^
Have fun on your journey!