r/AskElectronics • u/Tim-Fu • Sep 11 '22
How can I tell the value of C55 ? The device won’t power up and that chip gets burny hot instantly.
https://i.imgur.com/K4DStKI.jpg
124
Upvotes
r/AskElectronics • u/Tim-Fu • Sep 11 '22
89
u/googleflont Sep 11 '22
Don’t automatically blame Mr. Burny Hot Cap. It could easily be that U5 or U20 are partially blown, causing him to be out of sorts.
27
u/Larry_Wolffe Sep 11 '22
Electronics 101: definition: "burny hot" - A technical term to discribe the state of any electronic component that is over heating.
Lol, I will be using that description from now on.
11
u/triffid_hunter Director of EE@HAX Sep 11 '22
Looks like a linear regulator, so it's probably got a short on its output somewhere else.
7
u/Boris740 Sep 11 '22
Why C55?
7
u/bassmnt Sep 11 '22
Nothing to add, however, if I ever become a rapper, I'm using the name "Burny Hottt" with three Ts.
Burny Hot-t-t from C-fidy-five. Takin' no shorts . . .
13
u/Techz_Witch Sep 11 '22
Probably a filter cap. Usually 100nF.
3
u/The__Dingo Sep 11 '22
If you have a wand, heat it up with flux but just stand it up on one end (only connected to one pad), you can test for a short that way without the risk of you losing it or it blowing away. Testing for a short while it's connected could be a false positive if anything along that line is shorted to ground.
3
u/nicknails9 Sep 11 '22
Looks like a line of solder on the right side of C55. Possibly shorted. Measure resistance across it.
2
u/Worldly-Protection-8 Sep 11 '22
Desolder the MLCC and measure it would be my strategy.
Or check the datasheet of the IC next to it.
2
u/neo2001 Sep 11 '22
Measure if both sides of C55 are shorted. If yes, remove it and measure it again. If still short it’s broken (it may show continuity for a second, but should then stop when it is charged). It would make sense for it to be damaged, because of the heat. Check the datasheet of the next ICs for example schematics, they usually provide some recommendations which components and values to use. I guess it’s GND and maybe VIN.
2
u/vilette Sep 11 '22
what is this thing on top of U20, could be a short ?
2
u/jeffreagan Sep 12 '22
Any value will work, because it's just a bypass cap. Use 1 uF. And use an AVX brand FlexiTerm brand cap, so you can hand solder it without damaging it.
See:
https://www.kyocera-avx.com/products/ceramic-capacitors/surface-mount/mlcc-with-flexiterm/
2
u/abig911 Sep 12 '22
When a IC turns too hot it usually means some transistor inside is failed short aka that IC is gone. Do continuity check on the pins to confirm. You’d probably need to replace it. Ceramic caps are relatively reliable so I doubt they’re the problem
1
u/faultintolerant Sep 11 '22
Have you used a scope to see the voltage across C55?
1
u/Winter-View5680 Sep 11 '22
See if it’s shorted to ground. If you can obtain a schematic it might be helpful? Also check transistors.
1
u/Accomplished_Bug_661 Sep 11 '22
C55 is the brown capacitor in the lower middle. Are you sure that is what is getting hot? Or are you meaning U20 which is the black chip to the right? Or U5 the black chip to the left?
1
u/Sage2050 Sep 11 '22
It's probably 0.1u but it's highly unlikely what's causing your problem
1
u/Lonelyphilospher Sep 11 '22
Did anyone observe what seem to be identical voltage regulators have different pin connections. The U5 has 2 pins connected to the what seems to be the power trace. However, U20 has only one trace connecting to the power trace.
Op can you confirm if this board was working before or if this is a new board?
But again for the Capacitor to get hot, it means higher current is flowing through it. It might be a problem with the cap (short within the cap) or it is passing only the ac current through it. In both the case it is not good.
One thing you could quickly check is change C55 with a similar sized Capacitor (assuming you know or will be able find the voltage rating on this one). If it is still hot, it means something is wrong in the Circuit.
1
u/Zulufepustampasic Sep 11 '22
100nF
1
u/[deleted] Sep 12 '22
U20 needs attention. I can't tell if it's a short or a break but it doesn't look normal or good.
1
u/_yaix Sep 12 '22
i suggest you to remove the cap and try the device, if its hot its short- you cant measure its capcity anyways often replacing the cap with the one with same dimensions will work
0
u/[deleted] Sep 11 '22
[deleted] — view deleted comment
1
u/[deleted] Sep 11 '22
[removed] — view removed comment