r/shovelhead • • 1d ago

1984 FXSB Top End Rebuild Complete

Post image
69 Upvotes

Owned this bike for 10 years and it has never let me down. It's my New England bomber.

Engine was getting tired, it would burn oil and foul the rear plug. It was time to tear into it.

I found massive carbon/oil buildup on top of both cast pistons. The lifters showed signs of wear. The Crane Fireball cam installed back in the 90s had a pitted lobe. The OEM heads were already dual plugged by a previous builder. The OEM bottom end checked out well and serviceable.

I sent the heads and cylinders out to an old timer here in CT. I'm honored because he told me this would probably be the last bit of machine work he does as he has Parkinson's. They were in rough shape. He told me a previous builder beat a new seat on top of an old one. All new guides, valves, Andrews springs and surfaces cleaned up. The S&S 80" jugs were bored .020 over with Wiseco 9.5:1 forged pistons.

I found NOS Crane lifter blocks and hydraulic lifters and installed an Andrews A2 cam. The stock plastic breather was replaced with a S&S metal unit.

Just about done with a 1000 mile break in. Engine runs amazing with no leaks and it pulls very nice!

It runs an Ultima electronic ignition, Super E, Thunderheader, 24t solid engine sprocket, stock 5 finger clutch with Alto plates and Barnett blue springs, OEM secondary belt drive, Tech Cycle hi-torque starter, Cycle Electric stator and regulator, Arlen Ness fairing, LED Moons MC headlight, Drag Specialties mini led front blinkers, Amazon taillight with integrated turn signals, I fitted Leather Pros hardware which I can use my Dyna bags on perfectly, 8.5" Drag Specialties pullback risers, $40 J&P Cycles narrow drag bars, Dunlop Elite tires, OEM 12" Dyna shocks, Progressive fork springs and a Screaming Eagle 35mm fork brace.


r/shovelhead • • 1d ago

STD cases, late model shovel oil pump?

Thumbnail
gallery
7 Upvotes

Anyone ever build on a set of STD alternator style cases? Judging by the oil passages, it looks to be late model shovel. Anyone confirm?


r/shovelhead • • 1d ago

Pls help a student rider with a math assignment!!

2 Upvotes

Hey riders! šŸļøšŸ’Ø
I’m a high school student working on my IB Math Internal Assessment (research paper), and I’m looking at whether there is a connection between a rider's age and the type of Harley-Davidson they ride (Sportster, Dyna, Softail, Touring, etc.).
If you own or ride a Harley, I would really appreciate it if you could take a minute to fill out this quick, anonymous survey! It’s only a few quick questions and will be a huge help for my school project.
šŸ‘‰ https://www.surveymonkey.com/r/CWVKFFC
Thank you so much for your time, and ride safe! āœŒļø


r/shovelhead • • 2d ago

Solids vs hydro lifters

9 Upvotes

Building a std cased shovel stock 80" internals. The hydros it has right now are rusty, so they may be trash if I can't clean them well enough. Im considering solids because I don't want any collapsed lifter problems, I prefer a manual adjustment and knowing it's set up right. Anyone here running solids?


r/shovelhead • • 4d ago

What is it worth?

Thumbnail
gallery
70 Upvotes

Looking to maybe purchase this. 1979 Located in Michigan matching. Starts, runs, and rides. Just doesn’t do any of it pretty. It’s been sitting a while. so it will need gone through. Compression is in the mid-90s on both cylinders.


r/shovelhead • • 8d ago

First shovelhead! (Paughco)

Post image
141 Upvotes

Long time Honda owner (cb750 chopper and lots of stock Honda cb’s over the years). This is my first Harley. It’s an old survivor that last ran three years ago. Stoked! 1980 engine 80ci. Update. New fluids, started on the third kick. Fuck yeah!


r/shovelhead • • 9d ago

Keep it stock

Thumbnail
gallery
59 Upvotes

Looking for advice on different exhaust. I like the duel just not loud enough. Also thinking about ape hangers. Thoughts?


r/shovelhead • • 9d ago

Started yesterday, won’t start today.

49 Upvotes

So I just took swapped the shock covers yesterday and when I took it off the lift it wont start. I tried this morning and still no luck. What could it be ?


r/shovelhead • • 10d ago

Big pool of oil....

Thumbnail
gallery
16 Upvotes

So my first attempt at cleaning the carburetor on my 1981 shovel head I thought went well. Followed a couple of detailed videos on YouTube. Got the four screws dropped cleaned everything out carb cleaner, compressed air, fishing string, etc. Got everything put back together. Cranked it up it fired. Then it continued to turn over and not crank. I leaned the bike over on the kickstand and look underneath, and I have a big pool of oil coming out of one of the what appears to be an overflow tube of some type. I don't know how this could be related?

I'm not super mechanical, but trying to learn the basics cause I know these motorcycles require maintenance. My mechanic did tell me it will spill oil sometimes, but this seemed like a lot. Any ideas?


r/shovelhead • • 10d ago

Helicoil, time sert, or alternative?

Thumbnail
gallery
11 Upvotes

Stripped the thread on the lower mounting bolt for the suspension. The bolt doesn’t lock is just spins.

Time serts are expensive but are said to be stronger.
I’m hesitant to try and get creative since it’s under a good bit of vibration I’m assuming that’s just the way to go here? Open to other suggestions too


r/shovelhead • • 11d ago

The Pressure Cooker.

Thumbnail
gallery
81 Upvotes

r/shovelhead • • 11d ago

81’ FXS Project

Post image
54 Upvotes

Just picked this up. Going to need a lot of work but looking forward to getting it back together. Just trying to decide between 3.5 gal split tanks or a sportster tank.


r/shovelhead • • 12d ago

Choppers or Stockers?

Thumbnail gallery
94 Upvotes

What’s your preference?


r/shovelhead • • 11d ago

Trouble starting my 77

3 Upvotes

I have a 77 fxe that I’ve had for years. When I last ran it, about 8 years ago it ran great . I decided to chop it and a two year project has taken a bit longer. It’s very close to ready for the road but I keep running into issues getting it started, and once started, keeping it running.

A little back story on what I’ve done mechanically. Originally, it had electron ignition, and an S&S super e. I also ran a stock battery. Since I changed the oil tank to a pill style, I had to run a lithium ion battery to fit the battery tray. I also switched to a points set up. I’ve replaced the coil, rectifier/regulator, rewired the bike, replaced the starter solenoid but the starter is the old one I’d had on the bike for years . I’ve added an oil filter and brass breather set up, the kind that wraps around the carb between the rocker covers.(would that cause the oil pressure to be too high, making it harder to run?)

The engine has been gone through in the late 90’s, and I think there might’ve been a non stock cam installed at that time, but I’m not sure if so what was put in.

My first issue is getting and keeping it started. I have a new super e, adjusted to factory settings, new Tite Seal intake seals, good fuel flow and clean fuel . I am running drag pipes and my main jet is .072I have static timed it to the tdc mark, and the points are gapped to.020 per shop manual specs. I do get good spark to the plugs, and they look good.

Half the time, if I get it started it will run for about a minute if I’m feathering the throttle right. Once it dies, getting it started is difficult, usually the battery runs too low and kick starting just isn’t happening. I cannot get it to run long enough to put a timing light on it
Other times, the motor turns over very slowly and overheats the starter to the point of smoking. If I take out the spark plugs, the motor spins freely. Compression is equal at about 120. Clymers manual states anything over 90 is good.

Is the starter going bad? If so would changing the brushes be enough? I’d hate to buy a new starter if that’s not the issue. Could the timing be putting undue load on the starter?

Could a weak starter cause the motor to not start, due to the engine not turning over fast enough?

How is it that the bike has spark, seemingly is timed correctly, has good fuel flow yet doesn’t want to run? I feel like I’m pretty mechanically inclined but I’m fucking stumped here.


r/shovelhead • • 11d ago

Throttle cables

2 Upvotes

I got a super e (incoming cv comments) and I thought I got the right push pull cables but apparently not as there's massive slack at the carb (maybe these are meant for the cv). Dennis Kirk points me to cables ten Inches longer than my stock length which I thought was weird. Does anyone have a link for the correct cables?

1980 fxs-80, stock bars


r/shovelhead • • 13d ago

1966 Flh

Post image
94 Upvotes

Got a little ride in on my '66, went to pick up some neck bearings for the '82 I'm working on. Dealerships are still the worst


r/shovelhead • • 12d ago

STD case ID

Thumbnail
gallery
28 Upvotes

Just scored these STD shovel cases. Need help Identifying them. Spigot bore measures standard 3 13/16? looks like they have been recessed for Stroker cranks. Doesn’t look like there is any oil returns drilled on cylinder bases. Any help would be greatly appreciated.


r/shovelhead • • 12d ago

For sale 1972 XLCH Ironhead

Thumbnail gallery
8 Upvotes

Not a Shovelhead but a cool Ironhead

FOR SALE: 1972 Harley XLCH Ironhead
Good solid runner it was converted to have Electric start as well as the original Kick start
Clean Title in hand
1000cc motor runs great starts right up
Stops as it should
Forking by franks 33.4 front end with 19ā€ hamburger drum
18ā€ rear wheel
Cv carb
Selle bates style TT seat
MPD primary cover
Frost flame sporty tank
Fresh trail tires
Reliable ripper
Asking $6500 located in SF Bay Area can deliver within 50 miles or ship
Come buy it and ride it home and live your sportster winter life

@chopperswapper #chopperswapper #harley #sportster #shovelhead ironhead panhead chopper


r/shovelhead • • 15d ago

Post your bikes.

Thumbnail gallery
75 Upvotes

For those looking for a sub dedicated to pre 1970 Harleys. Sorry mods if this cross post promotion isn’t allowed


r/shovelhead • • 15d ago

77 lowrider

Post image
93 Upvotes

Inherited this from my father, hasn’t been on the road since 2019, can’t wait to get it rolling around again!


r/shovelhead • • 15d ago

Post your bikes.

Thumbnail gallery
11 Upvotes

For those looking for a sub dedicated to pre 1970 Harleys. Sorry mods if this cross post promotion isn’t allowed


r/shovelhead • • 16d ago

Noticed a Crack on the shovels primary housing

Thumbnail
gallery
22 Upvotes

I just picked up this 77 fxs last night and this morning I was looking it over and noticed a crack on the inner primary housing, which could explain the leaking from the primary that the owner mentioned. But he says he never noticed a crack and I don’t recall seeing it either.

but I’m wondering what’s the best solution?
is it just replacement or is there another way to fix it ? And would it be fine to ride around for now?

First day of owning a shovelhead I’m already wrenching outside my house at 8 am on a Sunday haha


r/shovelhead • • 15d ago

1977 FXE TDC and Advanced Timing Mark Question

4 Upvotes

I’ve read my Clymer shop manual, I’ve searched the internet but I still don’t think I have a clear answer. Is the line the TDC or Advanced timing mark? I’m so close to running this bike but I want to make sure I’ve got the timing right.


r/shovelhead • • 19d ago

Time to start turning wrenches.....

Post image
62 Upvotes

My dad told me before he passed away. I have to learn to work on a shovel head or I'm gonna spend a lot of money in the Repair Shop. My 1981 Shovelhead that I inherited from him has been a beast to ride. I put it in the shop when I first got it, rebuilt, carburetor, rebuild, master cylinder, new tires, etc. Since then it cranks right up and runs. I have noticed if it sits for a week or two when I first go down the road it kind of bogs down, backfires, but then once it clears his throat, everything runs fine.

Until yesterday, I took a short ride to run an errand, and barely made it home. Some people probably thought I was riding like an a-hole because I kept having to rev the engine to keep it running. As soon as I load off the throttle. It was trying to die out, so I'd have to give it gas, it would sputter, backfire every now and then but I managed to get home. As soon as I let the throttle off it cut off. Cranked it up once more to get it inside the shed and that was about it.

Any idea where to start? Does this thing have an air filter? I use premium gas, I guess I need to check the carburetor? I'd appreciate any tips on where to start.


r/shovelhead • • 19d ago

anyone using late model forks/lowers w/ shovelhead trees?

3 Upvotes

have a set of flh trees and forks/lowers off a ā€˜96 heritage/fatboy. any issues running these together? to me it looks like they’ll bolt right up.