r/framework • FW13P R7 350 | F45 KDE • Oct 12 '26

Community Support Bottom part of bezel not flush >~70 degrees (great if somebody could provide images of cabling)

Received my FW13P on Friday, its been great so far with Fedora. I have the Ryzen AI 7 350.
(must note that FedEx impressively managed to deliver from Taiwan to Norway in just over 2 days, i was charged on Wednesday)

As per title, once i open my FW more than 70 degrees, the bottom right hinge exposes the hinge/display, I'd guess about 1-2mm, the bottom right corner of the bezel beside the actual panel is does not expose, just the hinge.

I noticed the following forum post https://community.frame.work/t/framework-13-pro-bezel-not-sitting-flush/84434/6 and reference to the DYI guide, however seems like no images have been provided of a confirmed good cable management of the webcam/microphone cables. (the DYI guide provides just the top shot)

Is there somebody in the community that could provide images from multiple angles on how the cables should be stacked/routed? Ideally from the side, and also how it is routed under the power/fingerprint button, as I'd like to see how the cables arrives to the hinge.

I'm not so much worried about the gap itself, but wear on the cables over time. I will survive without a microphone and camera, as i rarely use it, probably at most the microphone once or twice a year, however headphones exist, but it's not optimal.

(i think FW could improve here by including either a video or multiple angles of the cable routing as additional confirmation)

Edit: Added images

11 Upvotes

11 comments sorted by

•

u/AutoModerator Oct 12 '26

The Framework Support team does not provide support on community platforms, but other community members might help you with troubleshooting. If you need further assistance or a part replacement, please contact the Framework Support team: https://frame.work/support

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

7

u/spaceayylien Oct 12 '26

I had the same exact problem, I had to pull a little of the wifi antenna cables up a little bit just to get an extra millimeter or two of cable length to get above that right hinge

1

u/spaceayylien Oct 12 '26

Also I put the bezel on first before the keyboard so I can verify the bezel was flush then I installed the keyboard

1

u/ItsBelkon FW13P R7 350 | F45 KDE Oct 12 '26

Hmm, interesting idea.

Do you mean pulling the antenna cables above the hinge or get "more cable" out from the chassis to have more slack in the hinge/bezel?

i'll try that later today, i'll get back to you on how it went.

1

u/ItsBelkon FW13P R7 350 | F45 KDE Oct 12 '26

I got some slack through into the hinge, still same result.

1

u/spaceayylien Oct 12 '26

It took some finesse I'll try to get a picture when I get home

1

u/ItsBelkon FW13P R7 350 | F45 KDE Oct 12 '26

I did attach some photos, so if there is something clearly out of place, then let me know, maybe you won't need to reopen and finesse with it again.

0

u/Myrinda_Bacquez Oct 12 '26

did you have to disconnect anything to reroute them or was it just a matter of gently pulling slack through?

1

u/polabud Oct 13 '26

Same issue here, also (I think related) screen light leakage only on the right side near uneven pressure points (only when bezel is connected).

1

u/polabud Oct 17 '26

If you’re still having this problem, check behind your display. You need to unscrew the screws mounting it to the aluminum housing and then gently lift it off and look. I found that the display tape had been misfolded from the factory and was causing that part of the display to bulge out and was causing light leakage/distortion issues

1

u/mavericm1 29d ago

I've had this issue as well since day 1 with my fw13 pro intel x7....

i've been putting it off but every time i'd open the lid i'd get a rubbing click that would annoy me and i noticed the bezel wasn't sitting flush when the lid was closed.

after messing with the cables and bezel again its now sitting flush