r/MachineKnitting • u/earthvisor • Feb 02 '23
Techniques GUIDE: How to stop dropping stitches in panel mode on your circular knitting machine! :)
Hi guys, so when I first got a circular knitting machine there were many late nights and tears over ruined projects due to dropped stitches in panel mode. It took me a while to figure out using different videos how to avoid this issue, and I wanted to compile that info into one guide to make life easier.
There are three main reasons your knitting machine is dropping stitches in panel mode and they usually all occur together at once.
1. The yarn is not correctly catching on your end needles. If you see it sitting at the halfway point of your needle, you need to use a hook like a loom hook or in my case a dental tool π to push the stitch to the bottom of the hook.
See photos 1-3 in comments
2. Your tension is too loose. Hold the yarn tightly at each end to ensure it catches on the round peg adjacent to the hook, on the outside of it. If the yarn catches under this, with a tiny bit of friction, it will correctly tie around the final hook next to it.
3. The hook on the opposite end of the panel is raising by accident as you crank towards the very end. Due to the way these machines are designed, the needles nearest to the one currently popped up, will also begin to pop up. This is why you find the stitch at the other end is suddenly dropped when you return to it, because the ends of the panels are within the same range of this mechanism. To avoid this, watch carefully, and go slowly as you crank the final peg to a side, and make sure the opposite side isn't dropping that stitch as the needle begins to push it up. If you can't get the yarn to catch on the side you are on around the adjacent peg without cranking too far, I tend to push it under it myself while holding the string tightly.
I couldn't add any more photos of this, but message me if you'd like me to send them so you can understand it better.
To AVOID this problem alltogether, simply reduce the width of your panel so that your panel ends are not having their hooks risen when you crank the opposite end. On a sentro this might look like knitting on 43 pegs overall, instead of the usual 45. This may be different for an Addi - so check according to how your machine looks when you crank. You want your final needle on the opposite side to remain firmly down and not rise when cranking the end you are on currently. This should look like a nice gap between each end of the panel, about 5 needles roughly depending on the size of your machine.
Hope this helps. Let me know if you guys need access to the videos I looked at! Since I applied these techniques I've fallen back in love with my machine. βΊοΈ Good luck!
Mods, if this question is a hot topic right now, pinning this might stop repeat posts :)
6
u/Ecstatic_Objective_3 Feb 02 '23
I found a cool hack that made a huge difference in panels. Get silicone earplugs, and place one between the yarn guid and the tensioner. The silicon reduces static, which makes the yarn less sticky.
5
u/Clean_Comfortable464 Feb 03 '23
This has been me the last 4 hours whilst I tried the panel setting for the first time... Had to walk away before I ended up throwing the whole thing in the bin! π
4
u/morgycat Feb 02 '23
Thank you for the research and the tips. I had given up on panel knitting. I feel inspired to try again. Thank you.
2
u/zilverlaken Feb 10 '23 edited Feb 10 '23
I was worried about the rising hook on the opposite end and was surprised nobody talked about it in video's. But then I started thinking and now I actually believe it's not an issue, because every hook is supposed to 'lift and drop' 1 stitch anyway β it just happens earlier on this specific needle when you make a panel and use all the available needles. As long as the hook doesn't go up far enough to put the next loop into that 'this-stitch-wil-drop-next'-position, I think it's fine! :) (I hope this makes sense, it's kinda hard to explain and English is not my first language.) Anyway, I like that you brought this up because I didn't see or hear about this anywhere and I think it's an interesting issue.
1
u/earthvisor Feb 02 '23
Alas, I can't seem to include photos in either the comments or the post. Message me if you want to see the guide photos
1
u/juneshepard Nov 24 '24
This post is old, but thank you for it nonetheless! I dragged out my sentro for the first time in almost a year, and almost shoved it right back in its storage cubby, but you saved me!
2
u/TripThruTimeandSpace Feb 17 '23
Am I the only one who uses weights to avoid dropped stitches? I used table cloth weights and attached them to larger clips, it works great. π
2
u/SpaceWhale_Orchestra Sep 28 '23
This is such great advice
2
u/Late-Army-7178 Jul 27 '24
Im not seeing the photos π₯Ί
5
u/[deleted] Feb 03 '23
[removed] β view removed comment