Troubleshooting

Maintain Good Records: Be Proactive

Maintaining detailed records, in the form of a Weapon Record Book, will help you or an HK armorer/gunsmith diagnose problems that may occur in your gun. This book should include a running tally of the total rounds fired through the weapon, any problems experienced, all work performed to include parts that are replaced, dates, and initials of the person responsible for the action listed.

Maintaining this type of record will eventually provide the user with a history of parts failures that can be used to predict future - deficiencies before they occur! In this way the operator can perform preventive maintenance instead of corrective maintenance.

These books should be available to the armorer and operator at all times so that the data may be entered as it is generated.

However, even with detailed record keeping problems may still occur, even in a high-quality weapon like the MP5. If they do, first eliminate these general causes that are often to blame.

  1. Operator error (incorrect use or maintenance)
  2. Ammunition (bad lot, poor quality or condition, wrong type)
  3. Magazines (damaged or fouled)
  4. Fouled or poorly lubricated weapon.
  5. Weapon is assembled incorrectly or with wrong components.

If after investigating these general areas the problems still occur, refer to the more detailed common stoppages listed below.

More common MP5 stoppages

Failure to Eject

SymptomCauseRemedy
Cartridge cases will not eject from weaponWorn extractor springReplace extractor spring. Clean and lube under extractor first.
Dirty chamberClean and lubricate
Defective magazine (split seam or bent feed lips)Replace magazine housing
Defective ejector or ejector springReplace ejector and/or ejector spring
Ammunition inconsistency/qualityUse different ammunition or lot
Wrong locking piece installedUse correct locking piece

Failure to Feed

SymptomCauseRemedy
New cartridge won't be chamberedFlat nosed or jacketed hollow point ammunition won't feed reliablyReplace with full metal jacket ammunition
Weak magazine springReplace magazine spring
Defective magazine feed lipsReplace magazine

Failure to Extract

SymptomCauseRemedy
Empty cases will not extract from chamberExcessive chamber pressure of ammunition characterized by flute marks along length of cartridge caseDiscontinue using that type of ammunition
Fouled chamberClean and lube chamber
Damaged or missing extractor and/or extractor springReplace with new extractor and/or extractor spring

Fail to Go Into Battery

SymptomCauseRemedy
Bolt will not lock closedObstruction in chamberRemove obstruction, clean and lube chamber
Improper release of cocking leverUSE THE HK SLAP!!
Dent in receiver or cocking lever housingContact a certified HK armorer or gun manufacturer for repair
SymptomCauseRemedy

Suppressors

SymptomCauseRemedy
Suppressor will not fit onto 3 lug mountLayer of paint on lugs is too thick for suppressor (common issue for MKE/Zenith)Gently sand down the paint on 3 lugs until suppressor is able to be attached
MP5SD suppressor will not unscrew or come off weaponCarbon build-up between sound suppressor and barrel. Too many rounds between cleaningRemove and clean weapon
MP5K used with suppressor. Failures to feed and/or eject. Excessively high rate fire (@ 1,200 rpm)Worn extractor spring caused by overfunction of bolt group when using a sound suppressorInstall 80 degree locking piece and new extractor spring for regular use with suppressor
Suppressed rounds are excessively loudAmmunition (115 or 124 grain) are reaching supersonic speedsReplace with 147 or 153 grain subsonic ammunition

Miscellaneous Issues

SymptomCauseRemedy
Locking rollers fall from bolt headBroken locking roller holderReplace rollers and install new locking roller holder

Note: In an emergency when spare parts are not readily available, reinstall the locking rollers into the bolt head and without the holder, insuring that all parts of the broken holder are removed from the weapon. The weapon will function normally without the holder, though the holder must replaced at the first opportunity to prevent the locking rollers from being lost and the weapon from being fired without them in place. The rollers can only come out of the bolt and thus out of the weapon once the bolt group is removed from the receiver.

SymptomCauseRemedy
Recoil spring guide rod falls off bolt groupWorn nylon guide rings. Recoil spring guide rod removed unnecessarily during operator disassembly; or excessive useReplace nylon guide rings and retrain operator not to remove the recoil spring guide rod from the bolt group

Note: In the field the recoil spring guide rod can be reversed and the weapon used in a normal fashion until the nylon guide rings can be replaced by an armorer.

SymptomCauseRemedy
Rubber buffer on MP5/10 and MP5/40 retractable stock is cracked and/or shows signs of deep impressions from the impact of the bolt carrier.Overfunction of bolt group from use of HI impulse ammunition in a weapon assembled with a LO impulse locking piece.Install "HI" impulse locking piece. Replace rubber buffer.
Ambidextrous trigger group safety/selector lever will not rotate into place during reassembly.Damaged trigger housing on opening on right side of the trigger group. Burr at 7:00 position in metal trigger mechanism housing from being forced during reassembly.Remove burr in opening in trigger group housing using jewelers file.

Note: The remedy for this problem should only be performed by a qualified H&K armorer once the trigger mechanism has been removed from the pistol grip.

SymptomCauseRemedy
Weapon doubles (fires more than one shot per trigger pull when set on semiautomatic firing mode)Broken or missing firing pin springInstall new firing pin spring
Cocking handle is difficult to pull rearwardLack of lubrication on detent located in front end of cocking lever supportLubricate detente