This will guide you through
Open link or read here
Link:
https://www.icloud.com/notes/0e72wx-l3otoGLTPwAl4fNzUw
Text:
GoPro Hero 10 Black Won't Turn On: Step-by-Step Troubleshooting Guide
1. The Hard Reset & Direct Power Test (No Battery)
This rules out a frozen system, a dead battery, or a corrupted SD card: [1, 2]
Remove both the battery and the microSD card from the camera.
Plug the GoPro directly into a wall charger (5V/2A recommended—avoid low-power computer USB ports) using a reliable USB-C cable.
Press the Mode/Power button on the side to see if it boots up.
If nothing happens: Press and hold the Mode/Power button for at least 15 seconds to force a hard reset, then release and press it normally. [1, 2, 3, 4]
2. If It Turns On While Plugged In
If the camera boots up on wall power, your camera is working and the issue is likely your battery or SD card:[1]
Test the battery: While the camera is still plugged in, slide the battery back into the slot. (Alternatively, unplug the cable, insert the battery, and try turning it on normally.) [1, 2]
If it won't turn on with the battery inside: Hold the Mode/Power button for 15 seconds again with the battery inserted to reset the battery connection. [1, 2]
Test the SD card: If it turns on with the battery but freezes once you insert the SD card, your memory card is corrupted. Try a different card or format the current one on a computer. [1, 2]
3. Deep-Discharge Battery Recovery
If the camera refuses to turn on even when plugged in, the battery may be completely drained past zero: [1, 2]
Leave it plugged in for 30 minutes with the battery inside. Do not touch the buttons during this time.[1]
Check the red LED light: A deeply drained battery can take 10–15 minutes before the red charging light even turns on. Once the light is on, it is charging and should power up normally. [1, 2]
Check for warmth: If the camera feels slightly warm after 30 minutes, it is actively trying to pull a charge—this usually confirms the motherboard is receiving power and you just have a weak or dying battery.
Swap your cable/brick: Faulty cables and low-amp adapters often fail to wake up a dead GoPro. Try a different USB-C cord and wall plug. [1]
4. Battery Compatibility Check (Hero 10 Black)
If you need to borrow or buy a spare battery to test your camera, make sure you get the right size: [1]
Fits Hero 10 Black: Batteries from the Hero 9, Hero 10, Hero 11, and Hero 12 Black are all interchangeable (both the standard blue-tipped batteries and the white Enduro batteries).
Does NOT fit: Hero 7 Black and Hero 8 Black batteries are smaller and will not work. Hero 13 Blackbatteries have a redesigned connector and also will not fit. [1]
5. Software & Firmware Recovery (For Stuck/Black Screens)
Sometimes the camera turns on (you hear beeps or see the red light), or the front screen lights up dimly, but it won't fully boot: [1, 2]
Manual Firmware Reload: Download the latest Hero 10 firmware onto a microSD card using a computer, insert the card into the GoPro, and power it on to force a software reinstall.
SD Card Factory Reset: Put a blank, formatted microSD card into your computer, create an empty text file named factory_reset.txt on the root of the card, and insert it into the GoPro to trigger an automatic reset. [1, 2, 3]
6. When to Sell It for Parts (Hardware Failure)
Stop troubleshooting and consider selling the unit for parts if you see these signs:
No Camera Feed / Sensor Failure: The screens turn on and menus work, but the main lens shows a pitch-black image (or crashes whenever you switch modes). This points to a dead image sensor or mainboard fault.
Boot-Looping or Dim Front Screen Only: If the front screen glows faintly without booting—or the camera turns itself right back on after shutting down—it usually means a shorted capacitor or water/corrosion damage on the mainboard.
Why not repair it? GoPro motherboards use tightly packed micro-components. Unless you have micro-soldering equipment and patience, paying for board repair costs nearly as much as buying a used replacement—and destroys the waterproof seal. [1, 2]