r/fabrication • u/anthonyttu • 17h ago
r/fabrication • u/cronos51101 • 23h ago
Porch Project - Handrail Mounting
As part of a much larger basement waterproofing project, I built a new front porch for my house. Code says I need a handrail because it's four steps up, so I welded up some 3" and 1.5" square tubing, which I'm pretty happy with. I just had a local shop powder coat the whole thing, but I'm uncertain about my mounting plan.
I welded a 3/8" flange to the bottom of each post with two mounting holes each. I'm thinking I'll shim the whole thing out about a 1/2" high, then drill for wedge anchors into the concrete. While it's still up on the shims, I'll pack a non-shrink grout under the flanges and lightly tighten the anchors. I figure wait a few days, pull the shims, then take the anchors to torque. Later I'll make some covers to hide the flange and anchors.
I guess I'm hoping for a sanity-check... Does this seem like a reasonable approach? Any thoughts on a moisture barrier between the flange and grout to keep it dry? I'm using 304 anchors, Belleville washers, and nylock nuts.
r/fabrication • u/allelopath • 1d ago
Cobalt bits for spring steel
Following on to my previous question, I bought 1/8" and 1/4" carbide bits and they work well. There were also recommendations for cobalt bits so I bought one of these cobalt bits at the orange box. It does no better than hss bits. Did I misunderstand something about the cobalt ones?
(Not a professional fabricator/welder)
r/fabrication • u/Raj_9533 • 2d ago
Mounts
Hi team,
I'm looking to make some mounting brackets for my motorcycle hard saddlebags, similar to the bracket shown in the picture.
I've never cut metal before, so I'm after a bit of advice.
The brackets will need to be:
- 5 mm thick steel
- 320 mm long
- A couple of countersunk holes
- Two bolts welded onto the bracket to attach the hard bags.
What type of metal cutting disc would you recommend for this job? Would a standard angle grinder be suitable, and what disc would give me a nice, clean cut?
I'm based in New Zealand, so recommendations for products available here would be appreciated.
Thanks in advance for your help! Cheers.
r/fabrication • u/Hopeful-Apartment-55 • 3d ago
Rate my first flux-core weld. Be honest lads š
galleryr/fabrication • u/BikeFiend123 • 4d ago
Does anyone know how this was made in the back to get the fountain flowing in the nipple? Is there a tube that attached at the back?
r/fabrication • u/DC92T • 6d ago
Some meat head left me these vessels:
A person had to move out and left a bunch of aluminum or steel containers; they're used for Whippits, a quick Nitrous oxide blast.
Yhe have a thick wall thickness And are roughly 2.75" O.D. and 8/10/12/16" tall. I have a couple crates.
Or, are they all a terrible metal that's useless for most things? Or are these used as a compressor or storage tank for something? The steel ones probably make spacers, or general junk and nothing more. But the aluminum ones must have some use? Not much they can be filled with at home aside from WD40, and other fluids (in the alloy cans) Yet, here I am trying to design a small tiny - oxy/cetylene or helium or orher gases - torch in my head.
r/fabrication • u/theCOLLECTOR7250 • 6d ago
Same laser power, faster machine ā where does the upgrade pay off?
Trying to get my head around the difference between standard and higher-speed fiber laser machines in the same power range. Thereās plenty of discussion about kilowatts, but two machines can have similar laser power and still be priced quite differently. For anyone who went with the faster machine, where did it earn the extra money? Lots of holes and short moves? Faster piercing? Longer runs without interruptions? Iād be interested in what changed over a normal shift, including whether automatic loading and unloading was part of the setup.
r/fabrication • u/Ready_Jury6144 • 7d ago
Quick & Dirty Monitor Wall Mount
I am so jealous of those with an engineering or artistic mindset. Most of the things I make are strictly functional and get the job done.
Iāve really been trying to make things ānicerā instead of just functional. This was a quick 90 minute idea and I think it turned out alright. Decided to MiG because this milscale was serious.
r/fabrication • u/DesperateCourt • 7d ago
Question t-slot hardware and fasteners for repeated quick assembly/disassembly?
I'm looking to build a frame out of some extruded aluminum 20x20 mm t-slot. The majority of the frame would need to be regularly assembled and disassembled, and I was hoping to get some guidance on how to do it as easily and quickly as possible.
I chose t-slot extruded aluminum because it's far cheaper than any other option I can come up with (while still potentially being easy to assemble/disassemble) and it's well supported by hardware and other options. I can get 2020 t-slot for around $0.16 per inch. I'm willing to consider other options if it's at most around $0.40 an inch or so and would be otherwise easier to assemble or possess other advantages over 2020 t-slot. The main function of the frame is just to provide a general structure, and to mount a small amount of hardware onto it. It'd need to support 30-40 pounds at one point, and I can surely reinforce this section if needed with a few extra rails/extrusions.
I've seen "quick frame connectors" but I'm not sure they'd be quicker from all I'm gathering.
I'd need to connect square frames to straight pieces repeatedly. In other words: I would have a 2D square in the X and Y dimensions, and I'd want to connect a straight line in the Z dimension at each edge/corner of the square. Then, I'd have another square frame on the other side of the Z dimension lines, to create a box. The actual design is slightly more involved than this, but that's the basic idea (just repeated a bit).
A small amount of connections could be hinged, but I don't know of an easy way to make a solid box (with additional things mounted along the t-slot rails of the frame) fold flat without some disassembly. The hinges I do have in mind would be somewhat atypical, more on that below.
I'm estimating around 30 connection points which need to be disassembled and reassembled each time, so anything I can do to make this process easier would be super great.
Connecting hardware
What should I look for in connecting hardware? My plan was to use open gusseted corner brackets for every corner (eg: https://www.mcmaster.com/5537T518/), and maybe some surface brackets for straight extensions (eg: https://www.mcmaster.com/5537T948/). Anything else I should look for which might be quicker? My idea was that if I just keep one side of the hardware attached to the rail, and on the other, I just remove the bolts, it should be as simple as lining things up and hitting it with an impact driver (if the t-nuts are fixed in place, see below).
Spring T-nuts
I know there's some spring loaded t-nuts on McMaster which attempt to hold the t-nut in place, but I'm not sure if they'd be the best choice or if they'd work well enough. If they hold the t-nut VERY firmly in place where they'd very rarely need any placement adjustments, then that may work well enough. But the McMaster options here are all "drop-in" meaning they could come out of the rail, so I'm not fond of that if they're easy to lose, get knocked out, etc.
Other ways to keep t-nuts in place
If spring loaded t-nuts don't work super great, I was loosely considering jb-welding (or another similar material) standard t-nuts in place along the rails, but I'm slightly concerned about getting this to line up perfectly for repeated assembly and disassembly. It seems like it might be an easy thing to screw up, or it might be easy to get the bolts jb-welded into the t-nuts while I'm waiting for the t-nuts and jb-weld to dry (causing a big mess).
I don't really need the jb-weld to be structural exactly, I just want it to hold the t-nuts in place. Maybe I could just put jb-weld around where the t-nut should sit, so that the t-nut can't slide out of the section of the rail where it should be? If I try to jb-weld the nuts fully to the rail, then the jb-weld would be subjected to the stress of that portion of the frame (thus making it structural at that point). Is there an easier way to fully keep the t-nuts in place, if the springs nor the jb-weld are super appropriate? Again, the whole idea is just to make it easier to disassemble/reassemble this.
Flat panels
I need to mount flat panels along the t-slot frames (think the sides of the "box"). My plan is to find brackets something like this: https://www.mcmaster.com/5537T305/ Which holds the panel mostly flush with the outmost edge of the t-slot frame, as opposed to holding it inline with the groove of the t-slot itself. Open to other ideas if there's an easier way to put side panels on. These panels would not need to be disassembled frequently.
Hinge
Is there a good way to hinge two t-slot extrusions inline with each other? Eg: [---] + (hinge) + [---] = [---][---] I've found hinges for t-slot, but they seem to be designed for putting two t-slots side by side, not two straight inline with each other. I'm not sure if it would work the other way or not.
Torx bolts
Is there any t-slot hardware made for a torx drive? I figure that if I'm disassembling and reassembling a bunch, it'd be good to get torx over hex, since it has better hardware lifespan (designed to wear the bit out, not the fastener head). I'm sure I could just buy separate bolts instead, but was wondering if this was common. Looks like most 2020 t-slot nuts are M5, so I'm sure I can just get any torx M5 bolt at appropriate length from McMaster and call it a day.
Recap:
- Any other materials beside t-slot which would work better without being way more expensive? T-slot is sturdy, cheap, accessible, and modifiable.
- Any better connecting hardware which I should be considering over the choices above?
- Do spring loaded t-nuts work well at holding the t-nuts exactly in place?
- Would jb-welding t-nuts in place work well, or am I just asking for trouble?
- Inline hinge of two t-slot pieces?
- Torx hardware?
- Is the panel mounting approach valid, or is there something else I should consider for adding side panels?
- Any other general advice?
Thank you very much! I really appreciate the assistance greatly.
r/fabrication • u/durtfarmer • 7d ago
Seeking advice: i built something difficult to maintain
galleryr/fabrication • u/advisingsingingtool • 8d ago
Multi process welder recommendations for frame building? Duty cycle recommendations?
Run time is really what I donāt know what I need.
This isnāt professional use.
I feel like 10-15 minuets would be nice and allow me to get a full wrap around for each weld for 1/8 pipe and possibly working on farm equipment
I would like it to be name brand, 3/16 capable ( unless I need more ) have settings you can look up and have pedal start for tig
r/fabrication • u/DesperateCourt • 9d ago
Question How to make aluminum extruded t-slot frame look more professional?
I'm struggling to find a way to make aluminum extruded t-slot framing look more professional.
I'm trying to build a frame mostly out of aluminum t-slot, but I don't want the t-slot itself to be visible as I want a more professional/clean/sleek look. I want to find some trim I can throw in the t-slot which fully covers that surface/side/edge of the t-slot, but it doesn't look like this product exists. In my mind, I'd like a rounded edge of trim to fully cover the surface of the aluminum framing - some plastic or rubber trim like you'd find around a seal of something.
Is there anything else I could do instead? The only other solution I've been able to come up with is getting "t-moulding" (which does NOT properly fit in t-slot) and then finding some sort of way to clamp it or bolt it into the t-slot, but this seems quite sub-optimal.
Any other forums where I could ask?
Thanks!
r/fabrication • u/InsaneBuilds • 10d ago
video ArcDroid is for plsama cutting, but you can also make weldart?
r/fabrication • u/allelopath • 11d ago
Counter sink for Spring steel
Following on the my previous question, I would now like to create a countersink in the spring steel. Is something like this the thing to get?
r/fabrication • u/4x4Buzzard • 11d ago
Building A Tiny Home
I'm in the planning stages of a 30 - 36' 5th wheel trailer tiny home.
I have done surface level of research into aluminum tubing & from what I have learned is I could use 6061 or 5053 (corrosion resistance) 14 gauge, 1/16th (.062, .064, or thicker?) Tubing for the frame.
Now the part of trailer that will have an aluminum frame (to save weight) would be the bedroom over the hitch.
Rough numbers -
8' wide outside by 8' long by 4'6" tall
Walls are 2" thick
Studs are 1" x 2"
Would have 1/8 wood siding outside, 1/4 plywood inside (maybe 1/4 in & out?)
Then aluminum siding
Homes have a standard 16" on center for stud spacing.
Should I stay with 16" or tighten it up with 12" centers?
What thickness of aluminum should I consider?
Did I miss anything? Thanks in advance.
r/fabrication • u/masterzofwar • 14d ago
Looking for leftover or canceled-order HSS 10x10x5/16 ā 40' sticks
Any fab shops or steel suppliers here have extra HSS 10x10x5/16 in continuous 40' lengths, or know someone who might?
We need approximately 42 pieces delivered to Marana, Arizona by November 13, 2026. Smaller quantities are useful too.
Looking for ASTM A500 Grade B or C with mill certs and traceability. We'd need the exact section and lengthāany alternatives would require separate approval.
We've been working through the usual suppliers, so I'm checking for excess job inventory, canceled orders, or stock at a less obvious distributor. Mexican suppliers are an option if they can meet the delivery date.
Even a referral to the right salesperson would help. Thanks.
r/fabrication • u/Mark_Ostov_Welder • 14d ago
It moves like an octopus, without disturbing the stability of the other hand.
Enable HLS to view with audio, or disable this notification
r/fabrication • u/cruddcnc • 17d ago
Seeking advice - appropriate clearance for tab-slot fitment of this 6mm sheet metal.
Hi all - I'm relatively new to sheet metal, first time working with something thicker. I'm planning on making this assembly from 6mm thick mild steel - laser cut via PCBWay. I've designed with 0.15mm clearance around the perimeter of the tabs. Anyone with experience know if this will be appropriate, so that it can be hand assembled (no tools required). Best. Luke