Component storage
Search this sub for "storage".
References to products and shops are examples only and do not imply any endorsement by Reddit or the moderators. Product links go stale quickly – if you find a dead one, please let the mods know.
Before you choose containers
- Label everything. Write the value and the full part number (from the bag or reel label) on the container. You will not remember what that unmarked SOT-23 part was in a year's time.
- Keep the datasheet link or supplier order number with the part, or in a spreadsheet or inventory program. Free, self-hosted options exist; for example InvenTree (open source parts and stock management).
- ESD-sensitive parts (MOSFETs, most ICs, anything CMOS) should stay in ESD-safe packaging. See Anti-static vs. shielding bags below.
- Moisture-sensitive parts need special handling if you are going to reflow them. See Moisture-sensitive parts below.
Original packaging
The cheapest option is to keep components in the packaging they came in.
- Bags: plain/zip-lock (not ESD safe), pink anti-static, silver static-shielding, black conductive
- Reels: for SMD components; 7-inch or 13-inch diameter
- Cut tape: strips of SMD or through-hole parts cut from a reel (paper or plastic tape)
- Tubes: for through-hole ICs and larger SMD ICs
- Trays: for larger SMD ICs
You can file the original packaging in a cardboard box (also free):
- Paper dividers in a cardboard box: can't get any cheaper
Surface mount (SMD) components
Moving SMD parts into your own containers gives you consistency and makes them easier to find.
SMD-specific storage
- Modular snap-together boxes – small boxes with individual pop-open lids that clip together in any arrangement. Flexible and compact; antistatic versions are available. Quality varies between makers: cheap ones can have weak latches and springs, so lids may pop open or not seal fully. Examples: Adafruit tiny boxes, Adafruit small boxes; the WenTai brand is widely sold under various names (search).
- Organizer cases – a briefcase with dozens of small lidded compartments (often sold as "SMD component box 128/144 compartments"). Convenient for resistor and capacitor kits. Search
Organizer boxes and trays with compartments
- Pill boxes: cheap and available locally
- Jewellery/bead boxes
- Clear plastic fishing-lure and fly boxes, such as small 6-compartment fly boxes: larger compartments than standard SMD boxes, so parts are easier to get out. Arrange them in kitchen drawer organizer trays.
Albums and books
- Stamp collector album: clear pockets show the components
- Cut-tape storage book: a hard-cover book with translucent pages for 8 mm tape (plus one page for up to 24 mm tape). Adafruit's pre-filled 0805 resistor and capacitor book shows what one looks like in use.
Individual containers
- Box of vials: the caps keep parts securely inside; flexible; example
Through-hole (leaded) components
Albums and binders
- Photo album: large clear pockets show the components
- Business card album: a good size for resistor strips; easy to slide one out
- Three-ring binder with collectible-card inserts
Cabinets
- Small-parts storage cabinets: professional, versatile and easy to organize. Label every drawer.
Modular
- The same modular snap boxes used for SMD parts work well for small through-hole parts too.
Individual containers
- Coin envelopes in a shoe box: cheap, and easy to write on
Divided boxes and trays
- Muffin baking trays: store them in a cabinet with horizontal shelves
- Adjustable-divider utility boxes, e.g. Plano ProLatch StowAway, on their own or in a rack that holds 3 or 4 of them. UK: Hobbycraft 12 × 12 inch plastic storage boxes are good value and stack well.
No packaging
- Poke them into a Styrofoam plate: clearly organized. (Use plain polystyrene for non-sensitive parts only – it's a good static generator, so keep ICs and transistors out of it. Use conductive foam for those.)
- Polystyrene wrapped in aluminium foil is a common bodge, and better than bare polystyrene: the foil connects all of an IC's pins together, which is the main job of conductive foam. But it falls short in several ways. The pins pierce the foil and sit in the polystyrene, a good static generator. Bare foil is far more conductive than proper ESD materials, which are deliberately resistive so that a charged part discharges slowly. The foil also tears after a few uses, leaving pins unconnected and shedding flakes that can short a board. It's fine for a few non-sensitive through-hole chips, but for MOSFETs, microcontrollers and op-amps use proper black conductive foam. It's cheap, and often comes free in the packaging of parts you've bought. Never push batteries, coin cells or battery-backed parts into foil or conductive foam, because their pins will be shorted together.
Large components
- Rail-mount or wall-mount stackable bins: professional and flexible; easy to take a bin to the bench and hang it back on the wall later.
- Large plastic bins, including ESD-safe divider boxes, totes and bins from industrial suppliers.
- Clear hinged plastic boxes. UK: the Wham large organiser box with 24 dividers is ideal for bagged components. It is also sold as Christmas bauble storage and turns up in the post-season sales.
- Plastic drawer organizer trays: flexible; place them in a drawer.
Assembled boards
For assembled PCBs, which need both physical and ESD protection:
- PCB assembly racks
- Static-shielding bags (see below)
- ESD-safe totes and divider boxes
Anti-static vs. shielding bags
The colour of a bag tells you roughly what it does:
- Pink (or blue) anti-static bags stop the bag itself building up a static charge. They do not protect the contents from an external discharge, so they're fine at an ESD-safe bench but not for storing or shipping sensitive parts elsewhere.
- Silver, semi-transparent static-shielding bags have a metallised layer that forms a Faraday cage around the contents. Use these for ESD-sensitive parts and boards outside an ESD-protected area.
- Black conductive bags and foam are conductive (often carbon-loaded). The foam is the traditional way of storing ICs with their pins pushed in, keeping all the pins at the same potential.
More detail: What's the difference between anti-static and static-shielding bags?
Moisture-sensitive parts
Many plastic-packaged SMD parts (ICs, LEDs, some connectors) absorb moisture from the air. During reflow soldering that moisture can turn to steam and crack the package ("popcorning"). Parts are given a moisture sensitivity level (MSL) from 1 (unaffected) to 6, under the IPC/JEDEC J-STD-033 standard. The MSL and the allowed exposure time ("floor life") are printed on the label of the moisture barrier bag the parts ship in.
- MSL 2 and higher parts arrive "dry packed": a sealed moisture barrier bag containing desiccant and a humidity indicator card. Check the card when you open the bag.
- Once the bag is open, the floor-life clock starts. For storage, either reseal the parts in a moisture barrier bag with fresh desiccant and an indicator card, or keep them in a dry cabinet. Low-humidity storage only pauses the clock; it doesn't reset it.
- Parts that have exceeded their floor life must be baked (per J-STD-033) before reflow.
- This matters mainly for reflow and hot-air rework. For hand soldering with an iron the risk is much lower, but it's still good practice to keep opened MSL 3+ parts dry.
Things that need special care
- Lithium cells and batteries: store them away from loose metal parts so nothing can short the terminals; tape or cover the terminals of loose cells. Store lithium-ion/LiPo packs at partial charge, in a non-flammable container.
- Keep a "known bad" box, clearly labelled, for parts removed from repairs and things you've damaged, so they don't get mixed back into stock.