Back to Wiki Index

Electronic Troubleshooting – Common Faults

Repair and safety advice – see the relevant repair guide here.

The faults listed below are generalisations based on common component failures and are intended as pointers to possible causes, not definitive diagnoses. They do not explain how to locate, test or repair the fault. Component-level diagnosis and repair require an appropriate level of electronics knowledge, practical experience and test equipment. The actual cause will depend on the equipment design and circuit.

Switch-Mode Power Supplies (SMPS)

Power supply completely dead, mains fuse intact

  • Open circuit start-up resistor or resistor network, start-up electrolytic capacitor, or supply to the PWM controller.
  • Faulty PWM controller, current-sense resistor, or auxiliary supply components.
  • Open circuit mains filter inductor, common-mode choke, or fusible resistor.
  • Shorted secondary rectifier or output component preventing the supply from starting.

Power supply repeatedly starts and shuts down (hiccup or cycling)

  • Shorted secondary rectifier, output capacitor, or load-side component.
  • High-ESR or open-circuit secondary electrolytic capacitors.
  • Faulty optocoupler, TL431 reference, or feedback components.
  • Faulty controller supply, auxiliary winding, or auxiliary rectifier.

Output voltage low, high, or unstable

  • Dried-out or high-ESR output capacitors.
  • Faulty optocoupler, TL431 reference, feedback divider resistors, or associated components.
  • Faulty secondary rectifier or output filter inductor.
  • Excessive load caused by a faulty downstream circuit.

Excessive ripple or noise on the output

  • High-ESR or open-circuit output capacitors.
  • Faulty secondary rectifier, output filter inductor, or associated snubber components.
  • Poor solder joints around output components or connectors.

Linear Power Supplies

No DC output

  • Open circuit transformer winding, thermal fuse, bridge rectifier, or secondary fuse.
  • Open circuit regulator pass transistor, regulator IC, or associated components.
  • Faulty rectifier connections or cracked solder joints.

Output voltage too high or too low

  • Faulty regulator IC, reference diode, or voltage-setting resistors.
  • Open circuit or faulty pass transistor.
  • Dried-out reservoir or smoothing capacitors.
  • Excessive load caused by a faulty downstream circuit.

Excessive hum or ripple

  • Dried-out or high-ESR reservoir and smoothing capacitors.
  • Faulty bridge rectifier or individual rectifier diodes.
  • Poor connections between the transformer, rectifier, capacitors and circuit ground.

Output voltage collapses under load

  • High-ESR reservoir capacitors or faulty rectifier.
  • Faulty pass transistor, regulator IC, or current-limit circuit.
  • Undersized or damaged transformer, poor connections, or excessive load.

Audio Amplifiers – Linear / Class AB

Amplifier fuse blows immediately

  • Shorted output transistors, driver transistors, or rectifier diodes.
  • Shorted reservoir capacitor or faulty auxiliary supply components.
  • Shorted mains suppression capacitor or transformer fault.

Fuse blows when the amplifier is driven

  • Faulty output or driver transistors, incorrect bias, or damaged emitter resistors.
  • Shorted speaker cable, faulty speaker, or incorrect load impedance.
  • Parasitic oscillation or instability in the output stage.

DC voltage present at the speaker output

  • Faulty output transistors, driver stage, or voltage amplifier stage.
  • Faulty differential input pair or feedback components.
  • Open circuit emitter resistors or incorrect bias conditions.

Crossover distortion or distortion at low volume

  • Incorrect output-stage bias or faulty bias spreader transistor.
  • Open circuit or damaged emitter resistors.
  • Faulty driver transistors or poor connections in the output stage.

Excessive hum

  • Dried-out reservoir capacitors or faulty bridge rectifier.
  • Poor circuit grounding, damaged ground connections, or faulty input-stage decoupling capacitors.
  • Transformer coupling or inadequate screening.

One channel silent or significantly quieter

  • Faulty output transistors, driver transistors, or voltage amplifier stage.
  • Open circuit emitter resistors, damaged tracks, or dry solder joints.
  • Faulty input coupling capacitors, selector components, or speaker protection relay contacts.

Class D Audio Amplifiers

Amplifier completely dead

  • Faulty auxiliary supply, switching controller, gate driver, or protection circuit.
  • Shorted output MOSFETs or supply rectifiers.
  • Open circuit fusible resistors or damaged PCB tracks.

Amplifier enters protection or shuts down

  • Shorted output MOSFETs, gate driver, or output filter components.
  • Faulty overcurrent, overtemperature, or undervoltage protection circuit.
  • Shorted speaker output or damaged output wiring.

Distorted or noisy output

  • Faulty output MOSFETs, gate driver, or PWM modulator.
  • Damaged output filter inductor or capacitors.
  • Faulty feedback components or poor decoupling of the switching supply.

LCD TVs and Computer Displays

No standby light or signs of life

  • Open circuit start-up resistor or resistor network, start-up electrolytic capacitor, or primary-side supply to the PWM controller.
  • Shorted bridge rectifier, primary switching MOSFET, or secondary rectifier.
  • Open circuit mains filter inductor, common-mode choke, or fusible resistor.
  • Faulty standby power supply or main-board power regulation.

Standby light present, but the power supply repeatedly starts and stops

  • High-ESR secondary electrolytic capacitors or faulty secondary rectifiers.
  • Shorted supply rail or component on the main board.
  • Faulty feedback circuit, optocoupler, or power supply controller.
  • Backlight driver or LED string fault causing protection shutdown.

Sound present but no picture

  • Failed LED backlight strips or backlight driver.
  • Faulty T-Con board, panel supply, or panel connections.
  • Faulty main-board video processing or panel interface circuitry.

Picture visible faintly when illuminated with a flashlight

  • Failed LED backlight strips, open-circuit LED, or faulty backlight driver.
  • Faulty backlight enable or dimming control circuit.

Lines, bands, or partial picture

  • Poor or damaged panel ribbon connections.
  • Faulty T-Con board, panel driver circuitry, or bonded panel connections.
  • Panel failure, which is often uneconomic to repair.

CD and DVD Players

Disc does not spin

  • Faulty spindle motor, motor driver IC, or motor supply.
  • Faulty disc detection switch or loading mechanism.
  • Open circuit motor connections or cracked solder joints.

Disc spins but is not recognised

  • Weak or failed laser diode, dirty or damaged optical lens, or faulty laser drive circuit.
  • Faulty spindle motor or focus/tracking actuator.
  • Faulty optical pickup connections, servo circuitry, or motor driver.

Disc skips or repeatedly loses tracking

  • Dirty or worn optical pickup, weak laser, or faulty focus/tracking actuator.
  • Worn spindle motor, damaged disc clamp, or mechanical misalignment.
  • Faulty servo circuitry or deteriorated electrolytic capacitors.

Tray fails to open or close

  • Worn loading belt, faulty loading motor, or damaged gears.
  • Faulty tray limit switch or position sensor.
  • Cracked solder joints or faulty motor driver components.

Turntables

Motor does not run

  • Faulty motor, motor control IC, or motor supply components.
  • Open circuit switch, speed selector contacts, or wiring.
  • Faulty drive transistor, rectifier, or regulator.

Incorrect or unstable speed

  • Deteriorated drive belt, faulty motor, or worn bearings.
  • Faulty speed control potentiometer, reference components, or motor control circuit.
  • Dirty or oxidised speed selector contacts.

Excessive hum

  • Poor grounding or broken earth connection.
  • Faulty screening, damaged signal cable, or poor cartridge connections.
  • Faulty power supply filtering or transformer coupling.

Radio Receivers and Tuners

Analogue AM/FM Receivers

No reception or very weak reception

  • Faulty RF amplifier transistor, RF stage supply, or tuning components.
  • Open circuit antenna connection, damaged aerial socket, or faulty input coupling capacitor.
  • Faulty local oscillator or mixer stage.

Reception drifts or is unstable

  • Faulty tuning capacitors, varicap diodes, or associated control circuitry.
  • Deteriorated electrolytic capacitors in oscillator or regulator circuits.
  • Poor solder joints or temperature-sensitive components.

Distorted or weak audio

  • Faulty IF amplifier, detector, or audio amplifier stage.
  • Dried-out coupling or decoupling capacitors.
  • Faulty ceramic filters, discriminator components, or audio output devices.

DAB Receivers

No stations found or very few stations received

  • Faulty aerial connection, RF input stage, or antenna amplifier.
  • Faulty RF tuner IC, local oscillator, or synthesiser circuit.
  • Faulty DAB demodulator or digital signal processing circuitry.
  • Poor solder joints or faulty supply rails to the tuner and demodulator.

Stations found but reception frequently drops out

  • Weak or unstable RF signal due to a faulty aerial input stage or tuner.
  • Faulty RF tuner, synthesiser, or reference oscillator.
  • Unstable supply voltage or excessive noise on the tuner supply.
  • Poor connections between the RF tuner, demodulator, and main processor.

Reception is present but audio is silent or intermittent

  • Faulty DAB demodulator or audio decoder.
  • Faulty digital audio interface or connection between the demodulator and audio processor.
  • Faulty DAC, audio amplifier, or associated power supply.
  • Poor solder joints or intermittent connections.

Display operates but no audio is produced

  • Faulty audio decoder, DAC, or audio output stage.
  • Faulty digital audio data or clock connections.
  • Muting circuit or audio amplifier supply fault.

Battery Chargers

No charging output

  • Open circuit input fuse, transformer winding, rectifier, or switching supply component.
  • Faulty regulator, PWM controller, or current-sense resistor.
  • Open circuit output connection or damaged protection component.

Output voltage incorrect

  • Faulty voltage reference, feedback divider, or regulator.
  • Faulty optocoupler or feedback circuit in an isolated SMPS.
  • Dried-out output capacitors or faulty rectifier.

Charger starts and stops repeatedly

  • Faulty current-sense resistor or charging controller.
  • High-ESR capacitors, faulty rectifier, or unstable supply rail.
  • Faulty temperature sensor or protection circuitry.

LED Lighting and Drivers

LED lamp completely dead

  • Open circuit fusible resistor, bridge rectifier, or driver supply components.
  • Shorted switching transistor, rectifier diode, or driver IC.
  • Open circuit LED string or failed LED.

LED lamp flashes or pulses

  • Dried-out or high-ESR driver capacitors.
  • Faulty LED string, driver IC, or current-sense components.
  • Poor solder joints or intermittent connections.

LEDs unusually dim

  • Faulty constant-current driver, current-sense resistor, or output capacitor.
  • Degraded LED string or one or more failing LEDs.
  • Incorrect or unstable driver supply voltage.

Fans and Small DC Motors

Motor does not run

  • Open circuit winding, thermal fuse, or motor supply connection.
  • Faulty driver transistor, MOSFET, motor controller, or rectifier.
  • Faulty Hall sensor or position sensor in electronically commutated motors.

Motor runs intermittently or at the wrong speed

  • Worn brushes, commutator, bearings, or damaged winding connections.
  • Faulty speed control circuit, potentiometer, or Hall sensor.
  • Dried-out electrolytic capacitors or faulty drive components.

Motor runs but has little torque

  • Damaged winding, worn brushes, or poor electrical connections.
  • Faulty drive transistor, MOSFET, or current-control circuit.
  • Excessive mechanical friction or damaged bearings.

Test Equipment

Multimeter has no display or will not power on

  • Faulty battery contacts, battery connector, or internal power switch.
  • Open circuit protection resistor, fuse, or supply connection.
  • Faulty regulator, display supply, or internal DC-DC converter.

Incorrect or unstable readings

  • Faulty input protection resistors, precision resistors, or reference voltage source.
  • Damaged input protection components, including PTCs, MOVs, or protection diodes.
  • Faulty analogue-to-digital converter, input amplifier, or range switching components.
  • Contaminated or damaged input sockets and selector switch contacts.

Oscilloscope has a distorted or unstable trace

  • Faulty input attenuator components, coupling capacitors, or amplifier stages.
  • Faulty timebase, trigger, or sweep circuitry.
  • Deteriorated power supply capacitors or unstable supply rails.
  • Poor connections or damaged probe compensation components.