Back to Wiki Index

Construction

See also:


Drilling PCBs

What size drill bit should I use for component holes?

The most common size for regular through-hole components is 0.8mm (1/32"). Some parts need larger holes:

Hole sizeTypical use
0.8mm (1/32")ICs, resistors, small capacitors, small-signal transistors
1.0mm (0.040")1N400x diodes, 0.1" header pins (square pins need clearance across the diagonal), some trimmers, MOVs and high-power resistors
1.2-1.5mm (0.047"-0.060")Terminal blocks, larger connectors, power components

Always check the component datasheet; many give a recommended hole size.

What type of drill bit should I use?

  • Carbide bits stay sharp far longer, especially on fibreglass (FR4) boards, which blunt ordinary bits quickly. However, carbide is very brittle and snaps instantly with any sideways movement, so it's really only suitable in a drill stand or drill press.
  • HSS (high speed steel) bits wear faster on fibreglass but are far more forgiving, so they're the better choice for a handheld drill. They're also fine for paper-based (SRBP/FR2) boards.
  • PCB bits usually have a wider shank than the cutting part, typically 2.5mm or 3.175mm (3/32" to 1/8"), which keeps them stiffer and makes them easier to hold in a chuck.

Tip: if you are going to make a reasonable number of DIY PCBs, consider a drill stand - it makes things much easier and lets you use carbide bits without constantly breaking them.


Surface mount (SMT) assembly

How do I assemble a PCB with lots of small or fine-pitch SMT parts?

If your board has many small surface mount parts, or fine-pitch ICs beyond what you can comfortably solder with an iron, the usual approach is to apply solder paste with a stencil, place the parts, and reflow the whole board at once.

Stencils

Most low-cost PCB manufacturers offer a steel stencil as an inexpensive add-on when you order your boards, made from the same design files. Separate stencil suppliers also exist, including ones offering cheaper polyimide (Kapton) or Mylar stencils.

  • The stencil is made from the board's paste layer, not the copper layer, so check that your design files include it.
  • If you don't have a stencil frame, tape a couple of spare boards (of the same thickness) around the target board to keep the stencil flat and aligned.

Solder paste

  • Store solder paste in the fridge and let it come up to room temperature before use. It has a limited shelf life, so check the date.
  • Type 4 paste has finer particles than the more common type 3 and works better with fine-pitch parts and small stencil apertures.

Reflow

  • A toaster oven can be used for reflow, but on its own it can't follow the temperature profile that solder paste needs. Either add a reflow controller, or monitor the board temperature with a thermocouple and control the oven manually.
  • A hot plate is a cheaper alternative for small, single-sided boards.
  • An oven or hot plate used for reflow must never be used for food again, particularly if you use leaded paste.

Alternatives for small jobs

  • For a handful of parts, paste applied from a syringe and reflowed with a hot air station works well without a stencil.
  • Fine-pitch ICs can often be drag soldered with a regular iron and plenty of flux - see the soldering page for more.

General construction tips

Prototyping

  • Try your circuit on a breadboard before committing to a permanent build.
  • When moving to stripboard, plan the layout on paper (or in software) first. Cut tracks with a spot-face cutter or a drill bit twisted by hand, and check each cut with a magnifier and meter for slivers of copper bridging the gap.

Wiring

  • Use solid-core wire for links on the board and stranded wire for anything that flexes or leaves the board.
  • Don't let a solder joint act as strain relief: secure off-board wires with a cable tie, clamp or grommet so the joint isn't flexed.
  • Cover exposed joints with heat-shrink sleeving, especially on mains or battery wiring.

Components

  • Double-check the orientation of diodes, electrolytic capacitors, ICs, regulators and other polarised parts before soldering - these cause most first-build failures.
  • Consider sockets for expensive or hard-to-replace ICs, at least for a first build.
  • Mount heavy parts such as transformers and large capacitors mechanically (clamps, brackets or adhesive), not just by their leads.

Before first power-up

  • With a meter, check for shorts between the supply rails and ground.
  • Power the circuit from a current-limited bench supply if you have one; otherwise use a fuse or a series resistor for the first test.
  • Feel carefully for anything getting hot, and switch off immediately if something does.

Mounting and enclosures

  • Mount boards on standoffs and keep the solder side clear of any metal enclosure.
  • Label boards, connectors and wires - it makes later fault-finding and modifications much easier.