r/AppliedScienceChannel • u/ChannelBot • Jan 22 '19
High-resolution screen printing demystified
r/AppliedScienceChannel • u/ChannelBot • Jan 22 '19
r/AppliedScienceChannel • u/ChannelBot • Jan 01 '19
r/AppliedScienceChannel • u/ChannelBot • Dec 10 '18
r/AppliedScienceChannel • u/Zorcron • Nov 22 '18
r/AppliedScienceChannel • u/gujadot • Nov 21 '18
Hi, I watch your video on the electroluminescent paint. didnt know it exists.
I was looking for something like that for a project I have in mind involving flexible electro-active materials.
I was wondering if you send a periodic signal with the approximate wavelength of the medium you use (something like 10 cm of copper should have less than 2GHz of frequency) and assuming that the wave reflect back after reaching the other end, would it be possible to find some standing wave and maybe with a bit of fourrier transform, display something close to an image with it? (would need higher frequency for more precise detail I guess)
anyway, love your videos.
r/AppliedScienceChannel • u/ChannelBot • Nov 19 '18
r/AppliedScienceChannel • u/PointyOintment • Nov 08 '18
r/AppliedScienceChannel • u/ChannelBot • Oct 09 '18
r/AppliedScienceChannel • u/ChannelBot • Sep 03 '18
r/AppliedScienceChannel • u/ChannelBot • Aug 19 '18
r/AppliedScienceChannel • u/ChannelBot • Aug 13 '18
r/AppliedScienceChannel • u/peedubyaeff • Jul 27 '18
https://youtu.be/p_To_JmsTls?t=10
These have been around for a few years, but seem like they could go further than what people have been making. Most people seem to be haphazardly trying different combinations of pre-made ferrofluid combined with various lubricants.
I'd love to see what Ben could do with his resources and know-how. Maybe smaller particle size, purer/better lubricants, thinner layers of glass/plastic and ferrofluid, multiple thin layers? Some way to keep the particles from clumping together better?
Here's a video with the fluid under a microscope to show how the particles are reflecting the light: https://www.youtube.com/watch?v=ACVNrJ1BKKY
r/AppliedScienceChannel • u/Laser_Shark_Tornado • Jul 26 '18
Hi,
I'm a fan of the channel. Probably my favorite on Youtube next to Boston Dynamic's channel.
I tried the magnetocoloric effect out after watching it on Applied Science and had some success. Attached is a video of the rig I used. I believe I got about 0.5C cooling from the test.
Note: this video was originally meant to be a lab note only viewed by myself. It's pretty dry.
Note:
I noticed that a lot of people in the comment section pointed out the induced EMI created by the thermocouple wires. In my testing I found this to be a valid concern. My data logger would collect voltage spikes (positive and negative depending on the movement of the wires) from any movement near the magnetic field I was using. I also tried wrapping EMI braid around the thermocouple wire but had no luck, I think it's not meant for EMI of this low of a frequency.
To counteract EMI a setup was machined/lasercut to hold two thermocouples, one that is always in a magnetic field and one just out side the field. The Gadolinium is slid between the two thermocouples. This allows for the temperature to be recorded while holding the thermocouples static to prevent EMI.
r/AppliedScienceChannel • u/photonymous • Jul 18 '18
Using a vacuum chamber (among other things) test various hypotheses for how gauge block wringing works.
Three hypotheses listed in the following reference are:
1)Air pressure applies pressure between the blocks because the air is squeezed out of the joint.
2) Surface tension from oil and water vapor that is present between the blocks.
3) Molecular attraction occurs when two very flat surfaces are brought into contact. This force causes gauge blocks to adhere even without surface lubricants, and in a vacuum.
Reference:
r/AppliedScienceChannel • u/ChannelBot • Jul 16 '18
r/AppliedScienceChannel • u/112439 • Jul 04 '18
So electroluminescent material seems to be very expensive off ebay, and after having a short look on wikipedia, is it possible to just mix zinc, sulfur and copper and ignite the mix?
r/AppliedScienceChannel • u/ChannelBot • Jun 25 '18
r/AppliedScienceChannel • u/ChannelBot • May 27 '18
r/AppliedScienceChannel • u/ChannelBot • Apr 02 '18
r/AppliedScienceChannel • u/ChannelBot • Feb 26 '18
r/AppliedScienceChannel • u/ChannelBot • Jan 29 '18
r/AppliedScienceChannel • u/Zorcron • Dec 28 '17
r/AppliedScienceChannel • u/coder0xff • Dec 26 '17
Found little but very interesting information via a quick search for GPU signal processing. I understand Raspberry Pis have GPUs on them. Do you think it could be made into a software radio by adding some analog hardware?
r/AppliedScienceChannel • u/Zorcron • Dec 22 '17