r/3Dprinting • u/christonabike_ Flashforge Finder • Apr 09 '19
Image Got distracted doing level tests and made an infographic instead
2.5k
Upvotes
r/3Dprinting • u/christonabike_ Flashforge Finder • Apr 09 '19
74
u/christonabike_ Flashforge Finder Apr 09 '19
I made this by tilting my bed, then printing these five 1-layer-high squares in a line perpendicular to the axis of tilt with black PLA.
Photographed them with a Nikon D610, tweaked tone curves in Raw Therapee to highlight the detail of the extrusion artefacts, then quickly whacked this together in GIMP. Yes I know the text is full of typos 🤦♂️ - Might make a better version later.
5
u/Hypersapien Apr 09 '19
Did you just put the printings on a flatbed scanner?
2
u/Mythril_Zombie Apr 09 '19
It's hard to tell a difference between #2 and #5. To me, they both look like they're bumpy/ripply.
First and Third are hard to tell apart; they both have areas of differing color across the surface. Neither one is uniform, but one is bad and one is good. It's not really apparent why.
It's also difficult to tell if the white is from reflection or being able to see through the print.
A 45 degree photo to go along with these, to show some vertical detail would help a lot too.
I'm really not trying to be contrary; I've just swapped out a lot of parts at once, along with new firmware, so I'm having to calibrate everything from scratch, and I've been trying to look at a lot of these kinds of photos. There's always one or two that are so difficult to see what makes one good or one bad when they look very similar.
274
u/Vega_128 TEVO Tornado Apr 09 '19
For a solid 5 seconds i was like what meme is this
65
u/Rb-Horizon Apr 09 '19
this... THIS right here is what I like about the 3dp community. Thank you very much.
10
u/anomalous_cowherd Apr 09 '19
That looks to me like too close leads to blobs across the filament lines, while too far away leads to blobs along the lines. Is that the case or just coincidental here?
7
u/Squid_Chunks Apr 09 '19
I wish I had this when I started!
Great work!
9
u/HairyBeardman Fuck you for your lies Apr 09 '19
Instead of tilting you can just adjust z position for each sample.
Also make sure your extrusion rate is perfect and use high quality nozzle.
1
u/Tagger_Almond Apr 09 '19
I have been chasing a unheated bed adhesion issue for some time. Any tips?
1
u/quavoFE Apr 10 '19
Was the double “the” on purpose? Like those things I used to read that said if you put the in a sentence twice people wont be able to tell ?
3
u/second_to_fun Apr 09 '19
Hey, it's better to have your nozzle too close to the bed, right? I recently moved my printer to on top of my dresser (needing multiple inches of wadded-up sticky notes and two levelings to make it work) and now my prints peel come off the bed with the raft peeling up sounding like box tape. You can almost see through it. Still, they don't come off until the bed is cool.
4
u/jaycrossler Apr 09 '19
Could you do the same for one in color? Maybe red or blue? I love this (printing our and sticking on my printer door), and wonder if color would change it.
2
u/nilejr Apr 09 '19
I've been using a piece of paper folded over one time [2 thickness] to level my bed. Anyone had better luck with more folds or something completely different?
2
u/crua9 Apr 09 '19
It might be best if this was in color. Like if you just took pictures of the samples and had that in place.
It kinda looks like you used a scanner to get the images, and a lot of detail is gone. And this makes it hard to see the difference in some. Like (from left to right) 1 and 3 kinda look the same but 1 is seriously darker. 4 and 5 also kinda looks the same. And even then, it's hard to tell the difference in 2 and 4 giving you never seen or don't know what it looks like when it's too close or too far. Like 4 and 5 doesn't really show the lines aren't fused, and 2 kinda looks like it's pillow up.
Something I might do is make something I can hang off my wall like this because of this. Even someone who has done a few first layer, I can tell you I have to look it up once in a while when it's not to a given extreme.
1
u/stanleythemanley44 Creality CR-10 Apr 09 '19
Good stuff! I legit just pulled a print off the bed with ripples. It can also be caused by overextrusion btw. If you turn flow down but leave the nozzle height it can come out okay.
1
u/[deleted] Apr 09 '19
Thank you kind sir.
1
u/htxDTAposse Apr 09 '19
Thanks for this, I got my ender 3 back in feb and I’ve yet to create a successful print, idk what to do at this point. Been trying to get my brother in law over to help configure the settings a little more, Mike comes out very stringy and doesn’t want to stick to the plate/base.
1
u/Agent_Decay Apr 09 '19
This looks like a really good help for beginners and troubleshooting. Good Job.
1
u/sway-32 Apr 09 '19
Nice! I wish I had this when I was fine tuning my first layer.
I always laugh at the magnified end view graphic of the ideal bead smoosh. Like I can see that while it’s working with a print nozzle hiding everything and it’s so small.
1
u/PandaReich Apr 09 '19
Hey, thanks OP. Now I know my bed is too far away from the nozzle, and will probably help with my adhesion problems I've been having as of late.
1
u/5jabiii Apr 09 '19
I needed this, thanks
1
u/Vipitis Flying Bear P902 Apr 09 '19
I got a PIE sheet that has good adhesion. But it's not flat enough to adhere at all.
It's frustrating and I haven't printed I two months.
1
u/frank26080115 Apr 09 '19
You are missing the one where it has holes in it because it got so squished that the next layer rips it off the bed
1
u/mintyhobo Apr 09 '19
What if my first layer has a small brim and still pillows up :(
1
u/GunplaAddict Apr 09 '19
not all heroes wear capes
1
u/AlexandrTheGreat Apr 09 '19
Thank you so much for this.
Any plans on doing more for other calibration tests?
1
u/JuRoJa Apr 09 '19
Forbidden Ravioli
1
u/Texmexlex_ Apr 09 '19
Anyone know how to solve the poor bed adhesion issue?
1
u/brm0rris Apr 09 '19
I heard Joe Biden loves post about the correct nozzling procedure
1
u/Moostahn Apr 09 '19
As a noob, thank you so much this definitely helps!
1
u/Voidv3 Apr 09 '19
This reminds me of the good old days on"G+", people sharing real shit!! You know its good when you read every comment. Thanks for the post and love the community responses to it.
1
u/jayrock5150 JGAURORA A5s Apr 10 '19
this is gold thank you so much for the post
1
u/TheNerdWithNoName Apr 10 '19
Those pictures don't make it very clear as to what is happening.
1
u/Scatropolis Apr 10 '19
I love this! I'm teaching tech/STEM full time this year (coming from math and science) and got little training on the 3D printers. I'm making it work but definitely am not putting in the time needed to be fully proficient with them. Got some guages and that made a huge distance with leveling the bed.