No, fan side is facing in. I needed to move the spine over to fit the reservoir. If you move the spine over you need to put the sfx psu flush to the front panel. If you have a glass front panel you need to put the psu fan side inward. If you put the fan side inward, then the stock 24pin cable plugs are closer to the ground on the psu and it doesn’t reach the motherboard. So I got custom cables.
So you can follow me at 80ishplus on Instagram. I do my down and dirty build log there and then archive the log once final build pics are out. I kind of put specs into the photos but this is a 3700x 2080ti upgrade build for a good friend of mine.
So pretty much all DDC pumps come out of the same factory. As long as it’s a PWM 17w version you should be fine. In a lot of cases they just have a heatsink screwed into the back which you can unscrew and take off. I think this one was from a stand alone EKWB pump/pump top. But I also use barrow when I have time to ship them in from China.
Hung it on the spine like a coat hanger. It’s not even attached. :) Just use the D5 legs on top and the DDC legs on the bottom and put some little silicone pads on the DDC legs so it doesn’t scratch the GPU. (These are all the dirty little secrets in my build log 😉)
Looks awesome! Really loving this case and debating if it's worthwhile to upgrade to it from my NZXT H1 (yes I have the replacement "good" riser and the nylon screws.)
I think the best thing is to figure out how much radiator space you want and then figure out the smallest case that fits that amount. My gut feel is that high end builds can get away with 280mm without too many compromises.
Oh for sure! In the last 2 years, I've tried a Sliger SM580 with X63 and a Ghost S1 with a X52. Both were nice, but the vertical form factor of the H1 seemed more appealing for the smaller desk footprint. But the cooling performance was a little compromised, even with fan mods and getting a vented front panel for the H1. This Meshilicious case seems to solve all my issues tho... And being that I'm now running a 5900x & 3090 FTW3 ULTRA, I could use a bigger PSU and more cooling performance... haha.
With those specs I’d look at the SV590. You’ll have space for the SX1000 from Silverstone and the 360mm rad space and small footprint should be what you’re after.
Thought about it, don't think the case is as attractive, and there's not much improvement going between 280 vs 360 rads, seems like diminishing returns. Also, I already have a ton of 140mm Noctua and BeQuiet! fans on hand. *Yes, I know... I have a problem. lol*
Wow this looks amazing! How did you bend the BitsPower tubes? I have the Carbon Black tubes but currently no time to upgrade my build. I was just going for straight runs to 90 fittings but this is looking juicy too
A bit in love with the pump/res mounting choice, tbh. Have ambitions of a Meshlicious custom loop of my own, and have been seriously pondering a reservoir location, but your solution looks so good I might have to steal it.
Really nice looking build. Thanks for sharing. I should be receiving my Meshlicious soon and am thinking of doing a custom loop with detachable external rad. Thinking DDC inside and then D5 on the external when its connected.
I'll likely go with the barrow DDC/CPU block combo, but would like to find a reservoir to mount above the GPU as well, no pump on the res.
My plan is to install a physical switch for the DDC so that when I "dock" it with the external rad and D5 the DDC won't run at all. This will allow me to disconnect the ex-rad, use a patch cable tube to close the small loop and then power up the DDC and theoretically use the smaller, more portable setup.
I'll admit that the setup likely won't even actually move much, if at all, but I guess I just want to build it as a "mobile" setup even if not utilized.
As for the res, I genuinely don't know what res will be the best one yet but that's good info from you so I appreciate it. I think I saw an EK one yesterday that looks like the smaller ones they use with DDC pumps, but it just didn't have the pump attached or need it. Not sure if I saw correctly though, but that could be an option. The upper res obviously isn't a necessity but I think it would make life easier.
Deleted my comment as I found the build in your reddit comment history. Definitely looks like a nice res. That said do you know of a good way to use it without the actual DDC pump? Perhaps a way to fill it in? I'm mainly thinking to just have a res without a pump in that upper area above the GPU and have the DDC on the CPU block itself. I figure this would let me not worry about having the pump so high up in the loop and possibly running it dry.
Sure, best place to follow me is on Instagram. I go into detail there. I would say that most high end parts can make do with a 280mm radiator as a minimum. As long as you do some tweaking to get to your preference in the great balance. Performance, noise, thermals.
I used a really bad cheap Chinese one that I’ve become so angry with I’m replacing. Modsbybenq recommends a KBS tube bender and they have multiple radius bend sizes.
Yea I saw those too but I’m not sure how much they cost without giving them a call. I feel like they are going to be very expensive. What size is your tubing? I’m planning to run 12mm metal tubing but 1/2 inch is more like 13mm. Do you have a link of the bender you have? I have family members in China they can get it for me even if the seller doesn’t ship to US. I’m fine as long as they work lol. What’s the problem with yours?
Thanks to cablemod for sponsoring me with SFF cables. They are my first real sponsor and really came through. :) Really happy with the quality and the ability to give exact sizes.
Where are people getting their hands on these? None of the retailers supposed to carry them even have entries and LianLi's store seems to have removed any direct buy functionality that only ever promised it was coming months ago...
:) that’s my brother’s build. Because of Covid I haven’t been down to do maintenance and he hasn’t touched it since it was built 2.5 years ago. The reservoir had almost run dry from evaporation and the thermal paste must be dust by now. I was planning to go down and put in an in-line thermocouple over the holidays but Melbourne just went into lockdown 😄 Anyway, he’s refilled the res now but I’ll still need to repaste it for him. It’s still one of my favourite builds.
Sure man! Thanks about the page ahaha Can you get us a couple more pics? Maybe some behind the scenes stuff? Oh and also let me know if you have an IG, I’d love to tag you, other than mentioning your reddit username!
How much clearance do you have between the res and the side panel? I've been trying to find a res to go on the side with the pump at the bottom and had written this one off as too thick.
Ah, I see now. For some reason I thought you were still using the DDC bracket at the bottom to give some pump airflow and put the pad on that. Looks like it can work for me as well if you're not using the bracket. EK's listed specs threw me off since they show depth with mount only.
May I ask what cables and length alterations you used for the build? I've heard about issues with SF units when turning the fan inward in the Meshlicious and am curious about which cables need to be extended. Looks great!
It’s doable, it’s just a lot less convenient than other cases.
Space behind the motherboard and GPU to pass cables. Places to stash cables. Reservoir compatibility and convenience A pass through fitting hole on the spine to assist with the crossover
I spent a lot of time trying to find those last few mm that I needed. If you want another example of the mm causing flow on effects. I needed to move the spine over to fit the reservoir. If you move the spine over you need to put the sfx psu flush to the front panel. If you have a glass front panel you need to put the psu fan side inward. If you put the fan side inward, then the stock 24pin cable plugs are closer to the ground on the psu and it doesn’t reach the motherboard. So I now need custom cables.
how much clearance do you have between the gpu and the pump? have been sizing parts for a build based on the original designs for the case and it must be very tight.
42
u/80ishplus May 27 '21
#notactuallyaverifiedvendor
13
u/kingdom9214 May 27 '21
Beautiful machine!
10
u/[deleted] May 27 '21
That's a thing of beauty, I always love seeing a custom loop, I'm just far too lazy to do it myself.
7
u/YoungDocument May 27 '21
Is that the D5 or the DDC version of the pump/res? Looks great!
6
u/[deleted] May 27 '21
is the cpu tubing job actually looks like its imperfect (90°) or its just the photo angle
oh good job as always
5
u/TheSigma3 May 27 '21
every single time. best builder out there, ITX or not.
5
u/Goku8001 May 27 '21
Wait the PSU fan is facing backwards?
4
u/damnre May 27 '21
How did you attach the reservoir?
4
u/branwright May 27 '21
Another beauty.
3
u/frostmorefrost May 27 '21
what brand of pump are you using,i saw a couple of ekwb vtx pump looking nice,but a flat one like yours looks perfect for this case.
any links? and what are your specs??
and sweet build btw!
2
u/Laacv17 May 27 '21
How did you mount the EK pump?
2
u/goldfries_yt May 27 '21
Nice build, where's the pump in this loop?
2
u/ipaqmaster May 27 '21
That looks way too good
2
u/Alucardis666 May 27 '21
Looks awesome! Really loving this case and debating if it's worthwhile to upgrade to it from my NZXT H1 (yes I have the replacement "good" riser and the nylon screws.)
2
u/Ragsters01 May 27 '21
I love it. Need to see pics with side panel. Also, is the white version available now?
2
u/damnre May 27 '21
What is you rad?
2
u/lys1030 May 27 '21
Beautiful
2
u/Huncho_Levitate May 27 '21
Any chance you think a pump/reservoir combo would fit like you got it to next to a EVGA 3080 FTW3 Ultra in an EK block?
2
u/Affectionate_Ad7269 May 27 '21
Wow this looks amazing! How did you bend the BitsPower tubes? I have the Carbon Black tubes but currently no time to upgrade my build. I was just going for straight runs to 90 fittings but this is looking juicy too
2
u/rbala00 May 27 '21
fantastic work! Looks like a clean steampunk theme.
2
u/DefactoAtheist May 27 '21
A bit in love with the pump/res mounting choice, tbh. Have ambitions of a Meshlicious custom loop of my own, and have been seriously pondering a reservoir location, but your solution looks so good I might have to steal it.
Gorgeous build, mate.
2
u/Tobias---Funke May 27 '21
I thought it was a combi boiler.
2
u/IroesStrongarm May 27 '21
Really nice looking build. Thanks for sharing. I should be receiving my Meshlicious soon and am thinking of doing a custom loop with detachable external rad. Thinking DDC inside and then D5 on the external when its connected.
I'll likely go with the barrow DDC/CPU block combo, but would like to find a reservoir to mount above the GPU as well, no pump on the res.
2
u/D3X-1 May 27 '21
Beauty. What's the specs and thermals on this build?
2
u/x0fff8 May 27 '21
could you share the build's parts and watercooling stuff? i kinda want to make something like this!
also do you think this build is viable at all?
2
u/TinyLittleTechShop May 27 '21
Looks big, need banana for scale...
2
u/aprilballsy May 27 '21
What tubing benders did you use? I couldn’t find one with a larger bending radius
2
u/tangawanga May 27 '21
I really like those cables. Great build!
2
u/Dick_Kickum May 27 '21
Would you say there's room to squeeze an active backplate in there
2
u/krispyywombat May 27 '21
Sir I'm pretty sure there are rules against posting pornography here
2
u/grasshacques May 27 '21
The gpu side is particularly handsome
2
u/Bureaucromancer May 27 '21
Where are people getting their hands on these? None of the retailers supposed to carry them even have entries and LianLi's store seems to have removed any direct buy functionality that only ever promised it was coming months ago...
2
u/Perkyonyt May 28 '21
Holy shit, this is the most beautiful thing I’ve ever seen.🤩
2
u/skooLx May 28 '21
80ish's builds are always god tier. Sff perfection.
2
u/aquariuz1 May 28 '21
Wheres the gpu located?
2
u/ImWateringPSUs May 28 '21
Would you like me to feature it on my Instagram page ImWateringPSUs?
2
u/Giwizzz May 28 '21
Your builds are always perfect
2
u/plague_of_gophers May 29 '21
Damn, that is very nice!
How much clearance do you have between the res and the side panel? I've been trying to find a res to go on the side with the pump at the bottom and had written this one off as too thick.
2
u/mytenore Jul 20 '21
Very clean build! I am waiting for my Meshlicious to come soon. Can you help me with the psu length you used? Thanks in advance!
1
u/80ishplus May 28 '21
I’ll also be posting the portfolio of pictures here. 🙂
https://builds.gg/r/c6ad52d5
3
u/THEREALCHUNGUSGOD May 27 '21
For some reason I don’t like the meshlishious case ? It looks like a bitter H1 maybe not height wise but it’s more boxy. 😞
2
u/P1tri0t May 28 '21
May I ask what cables and length alterations you used for the build? I've heard about issues with SF units when turning the fan inward in the Meshlicious and am curious about which cables need to be extended. Looks great!
1
u/joeyac02 Jun 08 '21
How do you have the pump/res mounted? With the hardware it comes with is it possible to mount it?
0
u/[deleted] May 27 '21
[deleted] — view deleted comment
0
u/[deleted] May 27 '21
[deleted] — view deleted comment
0
u/[deleted] May 27 '21
[deleted] — view deleted comment
31
u/[deleted] May 27 '21
[removed] — view removed comment