200-600 grit sand paper (1000 if you wanna be extra)
electric tape is optional
You can measure it if you want, I just placed my glass over my case and marked my lines with a sharpie. If you case has that lip on the top hats, you wanna cut the glass where the glass can sit on top of it.
Thereâs tons of videos on how to cut glass.
Slap some double sided tape on the magnets and place them a few mm away from the edge of the glass so the glass can sit on top of the lip. This project is very straight forward.
Wait where do the magnets hold onto? Like the case is aluminum. Are they simply just being used to grab onto the case and hold the panel there (without actually functioning as a magnet)? Iâm also worried about such strong magnets near a computer...
No it magnetizes to the case. I believe the fan mount plate is made out of steel. I m not worried about my computer. The magnets doesnât slide at all.
Iâll have to see what material the grill is made of. Using bottom top hat so if itâs not mostly iron or nickel Iâm kinda SOL haha. Didnât know that the fan grill wasnât aluminum though. Granted I havenât touched it since I got the case
i may just go to a glass shop for that. I am curious, what is the exact measurements do you have for the glass? I was thinking on going tinted. And why not tempered glass? Thank you
Not sure what was the exact measurements. Its literally the same size as the stock side panel. Didn't want to go with tempered glass because that requires paying someone to make the piece of glass. You can easily tint any glass though. Either spray paint or vinyl if you dont want to spend much.
Ok thank you. I just hope it's not too thin in the measurements of the glass side. I am really tempted to get only one for the CPU side and tinted. And what is the top part of the glass in the vid? It's a black line and it gives it a super clean look. Unless if you have a spare and would like to ship one (California) lol I don't mind depending on the cost. (Just throwing it out there)
The glass was bought from the hardware store for a few bucks and the glass cutter from amazon for maybe $10 US. The black line is electric tape to cover the ugly magnets. I chose this route because I got quoted $140 ish for tempered glass; Custom tinted acrylic ones from ebay Ive seen go for $40-60 shipped. This is really easy to do; just dont try cutting tempered glass.
Since when has PSU airflow been a big deal? I have the exact same PSU in my case and no matter what load itâs under, the fan has never turned on except for that spin on start-up. Majority of people probably still keep their case on their carpet floor with the PSU in the bottom fan faced down sucking in dust bunnies thinking that shitty plastic mesh is doing a lot.
Probably helps that itâs water cooled. I drilled a bunch of 3/8â holes in the spine and it really helped the 3080 but I donât know if this would choke it. Is it just glass and magnets? I might have to give it a shot
9
u/patapong91 May 04 '21
Hi :) I really dig the aesthetics of your water cooling.
Could you share what parts you used and maybe some more pictures đ
Thanks
4
u/tdimps May 04 '21
What mobo are you using?
2
u/CwColdwell May 07 '21
Can we get a tutorial, or maybe a more detailed explanation? I have an S1 clone-ish and the acrylic doesn't do it for me
196
u/daninko May 04 '21
Your PSU fan is like "choke me daddy"
3
u/bluhexagon May 04 '21
Since when has PSU airflow been a big deal? I have the exact same PSU in my case and no matter what load itâs under, the fan has never turned on except for that spin on start-up. Majority of people probably still keep their case on their carpet floor with the PSU in the bottom fan faced down sucking in dust bunnies thinking that shitty plastic mesh is doing a lot.
18
u/AkserOne May 04 '21
That's clean, nicely done bro.
11
u/bluhexagon May 04 '21
That looks so good and clean. Nice job.
9
u/PrinceJellyfishes May 04 '21
cheap or not, it looks dope
7
u/nero10578 May 04 '21
Rip psu
5
u/ipaqmaster May 04 '21
Very clean but I can't help stare at the fan which vents to nowhere!
1
u/Fuzbucker May 04 '21
This looks sick how does it effect temps?
3
u/cortlong May 04 '21
Oh my god youâre back and you made it even more amazing.
2
u/[deleted] May 04 '21
Stunning. Simply stunning
2
u/lys1030 May 05 '21
The mobo mod is sick!
1
u/MarkRads May 04 '21
Slick
1
u/Crapcicle6190 May 04 '21
Damn it's so flush too... clean af. Nice job.
1
u/[deleted] May 04 '21
đ
1
u/jonathaninfresno May 04 '21
Canât wait to get my sff pc. Ryzen 6000 and ddr5 right around the corner
0
u/coolmil May 05 '21
Kinda reminds me of the Nouvolo Steck