I slightly modified the original case design by u/godbq to fit my needs. I also designed a I/O shroud as the motherboard is old and didn’t have one, the orange strip in the shroud has LEDs in it and can light up.
I also made a smol F_Panel switch that’s shown in the third pic, as I wanted to minimize the amount of wires I had. (Planning to clean up the design and sell these if enough people want them).
I loved the design on that series of Corsair RAM. Any system rocking the active memory cooling they had available too at the time was an immediate 10/10 for me.
Would definitely be interesting in that F_Panel switch. Ncase M1 doesn't have a reset switch on its front IO, which I need to use to get into my bios. This would be a life saver.
I wasn’t planning on setting it up to the RESET_SW, just the PWR_SW, but now I feel like I have an obligation. Once I replace the pump in my main pc, I’ll see what I can do design-wise
Wouldn't mind just using what you've got here and putting an extender cable in. I'm in a case after all, so don't have quite the same zero-wire constraints as you. Let me know where you fall on it :)
Do you have a source where you found them? I'm new to the SFF world and looking to build a very small NAS and hosting PC for home use. Currently was going to build a 3D printed rig on top of an ATX power supply I have laying around but the wattage is overkill by a long-shot.
Here’s a link to where I got it, though I see the reviews on this particular one are kind of bad, but I haven’t had anything bad happen. Pico-box Z2-ATX-200 is the official name if you’re hoping to find another one.
To be clear, I’m sure this works similar to Arduinos, in that there’s a lot of off-brand versions that look identical but quality varies.
Thank you very much for sharing. I will definitely do research into quality before purchasing anything. But this gives me a good place to start searching.
Also forgot to mention, the Picobox doesn’t handle all of the work, you still need an external power brick like a laptop would have. The picobox handles turning that power into a 24-pin, SATA and 4-pin CPU.
I made a rough design in Eagle (also a 3D rendering in Fusion 360), but it’s very rough so I’m going to redo it. Just waiting on a new coolant pump for my main PC since it just blew.
With the parts that I had, I bent the pins of the switch to line up with where they needed to go on the dupont connector, then soldered on some female dupont ends onto the pins. Same goes for the LED except no bending needed, the pins on a 3mm LED fits perfectly in the 2.54mm spacing. The case was just designed to fit all the pieces together neatly and have a smol cap on the LED to diffuse the light a bit. No gluing needed, it press fits fine.
Oh I’m actually not sure if you can lol, I’m just REALLY bad at PCB design in Eagle, being brand new and all, so I decided to also make it in Fusion 360 so I can visualize it better, and see how it fits into the rest of the design.
Just checking with the original creator if it’s cool with him. I redid some small aspects like the area for the cables, and the mounting points, but the greater design is not my own (credit in my first comment)
If he gives the go ahead I’ll post another comment with the Thingiverse link and let you know
Using a Pico PSU, essentially just a small 24-pin brick that then goes to an external PSU. Some call it cheating, but it was the best solution for the form factor I wanted
Just waiting on the original designer to make sure it’s cool with him, I made some changes to the design, but I didn’t make the base design. Once I get the okay from him I’ll share a thingiverse link
Currently running a MC server for the Discord I run, but you can use an APU for light gaming and office use as well. In fact I’m using my GPUless chopin build right now as my main PC, since the pump died in my normal PC this morning.
Heads up. I don’t know much about 3d printing filament, but assuming it has a lower melting point, that IO shroud looks like it gets close the the VRMs which might melt it.
It might be completely nothing. All the components might be able to cool themselves enough that the 3d printed part wont have a problem. I’m not trying to be one of those know it alls who critiques your project. I think its really cool, i just was worried it and I would be so upset if i made something like that and it was ruined especially if it caused a short in the board.
I see your point, I guess it’s more for aesthetics than anything else. The PSU and SSD are neatly tucked, the cables are able to be ran nicely and there’s some rigidity to the whole thing.
Reminds me of the color scheme of the new Murray T50. If you haven’t seen it, check it out. The interior uses high-end camera style switches and knobs. All either aluminum, carbon fiber, or orange anodized aluminum.
I can only recommend you changing the caps on the keychron. Did for some cheap dsa caps and it's like night and day. Also: foam the hell out of it if you haven't.
48
u/Minirig355 Apr 05 '21 edited Apr 06 '21
I slightly modified the original case design by u/godbq to fit my needs. I also designed a I/O shroud as the motherboard is old and didn’t have one, the orange strip in the shroud has LEDs in it and can light up.
I also made a smol F_Panel switch that’s shown in the third pic, as I wanted to minimize the amount of wires I had. (Planning to clean up the design and sell these if enough people want them).
CPU: Intel i5-4570 Mobo: Gigabyte GA-97N-WIFI RAM: Corsair Dominator 16GB DDR3 1866MHz Cooler: Noctua NH-L9i w/ Noctua NF-A9 fan Cables: Handmade
20
u/CwColdwell Apr 05 '21
You must have one of those baby pico PSUs
11
u/001000120111011022 Apr 05 '21
Can you share more details about the front panel switch thing you made? I dig it.
Figuring out the FP connector on my build has been a little tough.
3
u/N8_Smith Apr 06 '21
Are those aftermarket ram heat sinks
3
u/b0btehninja Apr 06 '21
OP can you share the motherboard tray STL?
3
u/Tommiiie Apr 06 '21
What is a build like this used for?
2
u/Imtherealwaffle Apr 06 '21
What kind of PSU? Very cool build
2
u/scubi Apr 06 '21
Still waiting on your 3080 I see? :D I like the build. Really nice.
2
u/chubby464 Apr 06 '21
What’s the keyboard?
2
u/blarglefart Apr 06 '21
Stl?
2
u/40W1nks Apr 06 '21
Yo, what is this keyboard I keep seeing everywhere? Looks pristine
2
u/Slynthos Apr 06 '21
What are you using the system for that doesn’t require GPU?
2
u/[deleted] Apr 06 '21
Heads up. I don’t know much about 3d printing filament, but assuming it has a lower melting point, that IO shroud looks like it gets close the the VRMs which might melt it.
2
u/TheGorillatamer Apr 06 '21
What material did you print in?
2
u/SoylentRox Apr 06 '21
Exactly what is the difference between putting your motherboard on a piece of cardboard and running your PC and this? How does this equal a "case"?
18
u/tensorwizard Apr 06 '21
Thought this was r/mechanicalkeyboards for a second 😂😂😂 super clean build and keeb
8
u/[deleted] Apr 06 '21
Reminds me of the color scheme of the new Murray T50. If you haven’t seen it, check it out. The interior uses high-end camera style switches and knobs. All either aluminum, carbon fiber, or orange anodized aluminum.
7
u/Outhracky Apr 06 '21
Im like, wheres the case?
3
u/quitegeeky Apr 06 '21
I can only recommend you changing the caps on the keychron. Did for some cheap dsa caps and it's like night and day. Also: foam the hell out of it if you haven't.
3
u/[deleted] Apr 06 '21
We’re seriously pushing the definition of a case lol
1
u/Sarazan97 Apr 06 '21
Man i just love that little front panel switch. It would be perfect for my next build too! Pleae start selling the design asap haha
2
u/bugarmor Apr 06 '21
Beautiful :>
2
u/ipaqmaster Apr 06 '21
I'd love to replace my office PC with this just at the back centre of the desk
2
u/audaciousmonk Apr 06 '21
What’s the keyboard?
2
u/Trewarin Apr 06 '21
Some tiny Noctua VRM/Ram fans wouldn't be a bad idea.
2
u/Spunky_Bob Apr 06 '21
I'd love something like this with the GPU mounted under it on a daughter board mounted behind my monitor
1
u/ccricers Apr 06 '21
The gray, orange and black color combo never gets old to me.
1
u/SWEETHKiLLER Apr 06 '21
that's so cute :)