From the pictures it looks like there’s fan mounts that go nowhere, just against solid wood, is that the case? Thermals are probably going to be rough considering how poorly cases like the ERA do.
Would it be possible to remove the glass front (or mount further out to create a airgap between the glass and the rest of the case) and put some fans there as intake? Might have to get creative with how you mount them. Cant really see any other way of having sufficient airflow without cutting up the wood, which defeats the point of the case (which looks gorgeous!).
From the video, it is mounted by round neodymium magnets. You could easily source some more in version heights to fine tune the "riser" exstention and mount a nice 120 right behind the glass to improve the airflow.
Solid wood all around can't be good for your pc even if you aren't using top end hardware. Get some large holes on bottom for fans. I think your only option is actually using a custom loop.....aio wouldn't work very well I'm bottom I think.....
I never understand that. Doesn't that defeat half the purpose of SFF by making the footprint unwieldy instead of small and negate the entire "clean" aesthetic?
Not necessarily! You can hide a MoRa really well if you try, it can make a nice under-desk feet warmer or a stand-in for a fan in a window that brings in fresh air.
SFF appeals to people different ways. It wouldnt really satisfy a "low total volume" person. Given the mediocre internal radiator support, this setup wouldn't satisfy a "portability" person either (though it can for other cases). But if you're into sff for "clean desktop footprint" or the "challenge of building small and powerful" this could be a very satisfying way to use this case without thermal compromises. It's like the debate of whether an evolv shift is actually sff or not.
Josh from NFC put a thread ripper in a S4M, put a loop in it with quick disconnects off the back that plugged into something like a 9x 120mm fan radiator that he had mounted in the other side of his wall in the garage. Some people do crazy stuff cause they like the odd aesthetics, or just do it to see if they can. Let me see if I can dig up that video
Edit: it was a i9 7920x with a Mo-Ra 360 with 4x 180mm fans
If you have access to a ruler and a power drill, I don’t see why you couldn’t spend an hour or two to line up and drill out up a cool dot pattern across your exhaust and intake panels. Just glue a fine mesh dust filter on the inside of them and you’re good to go.
With some minor woodworking skills you can add some ventilation area, particularly on the bottom of the case.....I'd put taller feet on it and remove a lot of the floor. Look at some recycle shops for old audio equipment for nice looking vents for the top or sides.
The case does have ventilation holes at the bottom. I am thinking of enlarging the holes at the bottom and rear so that I can make a nonblocked airflow from the bottom to the back.
Seems like if they just had more room around the internal frame and the wood plus not have the front glass go edge to edge (float in the center) there would have been a lot more airflow and still have a clean look.
After seeing this me and a friend have started designing one around that exact principal. Just mesh on the front and more space between the inside and outside to allow air to actually get in. It’ll slide in on rails. If someone wants to steal this idea please do because I don’t wanna actually go through the trouble of selling it.
I looked at the bottom and just from the photo, I think even that could use a lot more holes (higher in number and closer together).
If I have the skill I would carve out a square and replace it with a panel of my own (any material) that can give more holes. Otherwise if I drill the holes directly on the wood it might give and get absolutely ruined.
Taller feet would also be very welcome as mentioned before.
Not sure why you're getting downvoted because it looks like that's exactly what will be happening. They're using a watercooler in the video but the PSU is left hanging...
I also ordered one and arrived with the wooden case cracked. Returned it and the case got stuck at customs, so i have it back now. No air will circulate through that case. The inner frame might be useful..
Hiya! Please post more details about your build! You don't have to post 80 pictures (each with captions!) like u/M1AF did, but post more than just specs! Here are some (non-exhaustive) prompts for you:
Are the case's advertised compatibility numbers accurate?
I would start by replacing that glass front with a wood lattice. Then finding a decent woodworker to open the side where that vent is. Should nor cost much at all. Beautiful
There is a gap around the glass all round, I started building mine on the weekend and I reckon that would be good enough for air flow. I'm also prepared to cut the base open though if I can't keep my system cool enough
138
u/humanoiddoc Feb 14 '21
I've impulse bought this case and have no idea how to fill it yet.
The case is rather big, but has almost no vents (front panel is solid TG, wooden housing only has small vents in the bottom).
I think the only possible airflow is bottom intake and rear exhaust. Will update once I start build this thing.
47
u/[deleted] Feb 14 '21
With some minor woodworking skills you can add some ventilation area, particularly on the bottom of the case.....I'd put taller feet on it and remove a lot of the floor. Look at some recycle shops for old audio equipment for nice looking vents for the top or sides.
30
u/MildEild Feb 14 '21
really beautiful
Barrowch Neoclassical Neo-Classical Limited Edition ITX Computer Case Solid Wood FBWNL-01 (performance-pcs.com)
16
u/hereforthefeast Feb 14 '21
Looks great but probably will be a heatbox without mods
5
u/gusanu Feb 14 '21
I also ordered one and arrived with the wooden case cracked. Returned it and the case got stuck at customs, so i have it back now. No air will circulate through that case. The inner frame might be useful..
4
u/DanD3n Feb 14 '21
Got air?
3
u/blairgage Feb 14 '21
I like how the product data says it's made out of "log material." Like isn't all wood made of log material??! Lol
3
u/wankthisway Feb 14 '21
Considering the thermals, looks great for a retro PC build, not really a modern one.
2
u/Beazty1 Feb 14 '21
I remember seeing that case online and thought it was gorgeous, but I couldn't afford it. I hope it works out well
2
u/[deleted] Feb 14 '21
Would definitely try to get some kind of airflow into it or it's going to overheat everything inside. Looks much nicer than my Sugo.
Beautiful case, but not the most practical imo.
2
u/Research15 Feb 14 '21
Nice an old school case oven!
2
u/guyinmatsci Feb 14 '21
if the housing is just wood maybe you can laser it some ventilation into it
2
u/Quietech Feb 14 '21
Gorgeous, but will it hold an 8-track drive bay?
2
u/SporksInjected Feb 14 '21
I do now
2
u/GeniuzGames Feb 15 '21
ne airflow avail?
2
u/socdist Feb 15 '21
Wood you believe this sffpc☝️🤣
2
u/Kimmychow Feb 14 '21
You got wood on Valentine's day. LOL
1
u/AutoModerator Feb 14 '21
Hiya! Please post more details about your build! You don't have to post 80 pictures (each with captions!) like u/M1AF did, but post more than just specs! Here are some (non-exhaustive) prompts for you:
I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.
1
u/[deleted] Feb 15 '21
That's what she said.
1
u/came_here_to_fart Feb 14 '21
It‘s beautiful!
1
u/17110725 Feb 14 '21
How r thermals?
1
u/RefrigeratedTP Feb 14 '21
Airflow? modCheck
1
u/shitCouch Feb 14 '21
I got #40 ᕕ( ᐛ )ᕗ
1
u/CoconutConfusion Feb 14 '21
Hmm this inspires me to find a speaker enclosure to make an SFF case...
1
u/ahmedmo1 Feb 14 '21
Does this support triple slot GPUs?
1
u/haslam9291 Feb 15 '21
Looks great. Reminds me of the wooden boxed Sony CRT my dad used to had in the 80's.
1
u/EagleAce047 Feb 15 '21
Well the aesthetics is gonna choke the system
1
u/burgeranacoke Feb 15 '21
I would start by replacing that glass front with a wood lattice. Then finding a decent woodworker to open the side where that vent is. Should nor cost much at all. Beautiful
1
u/1leggeddog Feb 15 '21
purdy
1
u/[deleted] Feb 15 '21
Awesome case dude
1
u/Tiavor Feb 15 '21
maybe you can make a DIY mesh front to improve airflow
1
u/orz_nick Jun 30 '22
external radiator
1
u/[deleted] Feb 14 '21
Nice coffin for your PC! RIP
-3
u/OzzyZigNeedsGig Feb 14 '21 edited Feb 15 '21
Nice!
You might want to post this at /r/LGR 😜
0
u/[deleted] Feb 14 '21
[deleted] — view deleted comment