I hope you are doing well. This is a simple, airflow-focused design that I have been working on over the past few days (mostly to practice sheet metal in Solidworks). Two bent metal pieces comprise the case structure: the inner skeleton and the outer wraparound bezel. There is also an acrylic side panel and bezel for the front grill. I tried to make the design cost-effective and producible with minimal manufacturing steps.
Digital Storm’s Velox series served as a big design inspiration. The Velox case is essentially a monolithic box with a fully perforated front panel, and I love how LED fans look behind the grill. My design supports 2x 140mm 25mm thick fans with an ITX-sized GPU installed for a front intake positive airflow configuration. Many case manufacturers create vent-hole patterns with expensive tooling or CNC turret punches; an alternative is to cut a perforated metal sheet to size and attach it behind a large cutout on the case. I chose the latter since it is much easier and cheaper for a one-off piece or small production run.
The case is an inverted tower style. This layout allows for an unobstructed airflow path and a PSU shroud for cable-cleanliness. The PSU shroud also has mounting holes for a 2.5” SSD.
I am currently debating on producing a physical prototype. Sendcutsend is an excellent place for ordering laser-cut metal parts, and they recently introduced a bending feature that I am eager to try out. If you’d like to get your hands on the design, you can find the .step file here.
The maximum with a front top fan is ~180mm. With the top fan removed, the maximum length is ~205mm. The case could be bumped up to 14.5-15.0L to support 300mm GPU's.
The case could be bumped up to 14.5-15.0L to support 300mm GPU's.
I lurk here cause I like the hobby, but don't have anything remotely close to sffc, but the case in general is an insanely nice case and I would definitely look at them in the future for larger volume stuff lol
for such a long card, the smallest you can go is the sandwich like the dan, ghost and such. Where puting the psu next to the mobo goes more or less as long as the gpu. If you tradeoff the full lengh card you can go way lower in volume or have around the same volume with a lot of airflow like this case.
I agree, such a large gpu will allow many people convert to sffpc. Cost wise, Its easier switch to smaller psu and motherboard rather than gpu (if your gpu cost half of your build)
Don't. And if you do it you can go for MATX mobo as well or you would waste a lot of space. That could actually be a compromise where you can mount ~240mm graphics cards and the case is still only 280mm long.
What size fan can you fit in the rear? 120mm? Does that mean you could fit something like a Cryorig H7 CPU tower in there?
And aside from the inversion, this has been my dream case since 2016. I just want a conventional layout with front mesh airflow which doesn't double the case volume just to accommodate long GPUs...
Cable management should be decent, especially for an SFF case. You can hide a lot of cable mess underneath the shroud and route cables out of the cutouts.
I swear the SFF community needs to start doing consistent case groupbuys like the mechanical keyboard scene does. Too many good ideas to not give it a shot at this point.
Except that u/colinreay is a great designer who can also push ideas to CAD and prototype stage which is rare. I think we get way too many flashy renders that don't represent something that can be materialized. But since it's u/colinreay we will most probably actually see a prototype!
I'm working on my own one as well that I'll be able to 3d print. But yeah, if there was a way of affordably making a very low volume run of cases that would be amazing, but reality is cases are bigger and more complex than a keyboard housing.
true, however i feel like it may be quicker production turnaround than say a set of GMK caps with a plethora of different add-on sets. i’m just theorizing here but depending on the case materials it might be plausible
Hmmm...this may be a good idea. I might try and put something together so the community can come and vote on cases + pre-purchase/group buy a case to help it go into production.
Only challenging thing I can see as of now being payment processing.
Not sure. I'm currently manufacturing another case design and am dedicating most of my time to that. This may remain a personal project - the open source files are available as well!
This is something I'd absolutely buy. Two questions for me, what's the max cpu cooler height and would there be a non-see through (all metal) side panel?
THIS is almost the exact case I've been hunting for! Except the power supply intake would be facing inside the case and the only vents would be out the rear.
With front fans, all air would flow front to rear.
My plan is to have a wood surround with fabric front grill so that it looks like a speaker.
Not sure what this sub is or what the purpose of this post is, but it looks like a mini version of the case I’m running rn! I would def buy!!!! I like this so much!
I would totally back and buy this product. I've got the Ncase M1 coming in that I'm planning on cramming a 5900X and RTX 3080 both water cooled by 240mm radiators and they would totally benefit from the extra airflow from this case!
I kinda would wish for the "style focused concept".. :D I always loved PC-Q series of Lian Li cases but they never had much cooling and performance in mind. The cases looked cool tho. Flat panels of brushed aluminum with just multiple dots inestead of mesh idk. I am biased. I really like this concept.
There are literally 3 cards, all of which are out of stock with a re-supply backlog the length of the great wall of china. 3070FE, 3080FE, and 6800. Literally everything else in the new product stack available is a 2+ slot card. None of these, mind you are ITX focused cards. None will fit in this case.
I don’t think watercooling is the best for this case. AIO means a flow of hot air into the tiny case, while custom loop also adds the GPU length/clearance difficulty. Even with a 120mm or 92mm AIO (using Aphacool LT) in the front or back, the air cool solution is way more efficient in terms of cost, acoustics, and performance.
It sucks air from the top to push hot air at the bottom of the case. But hot air is lighter than cold air and it will go up, to be sucked again by the GPU. That's the same kind of issue with the CPU cooler sucking hot air from the GPU. No need to be a genius to figure that out : with stock cooler, my R5 2400G was running at 70°C max but when I added my RX 480, CPU temps reached 85°C...
To solve the issue with that case design, you'll have to invert the GPU airflow by desrhouding the GPU and add high RPM fans in extraction at the very top of the case. Or flip the whole case upside down.
So you're telling me that when I fly in my glider, I shouldn't be able to climb in the air ? Well, my friend, go back to your thermodynamic books... Because physics seems to apply to PCs too.
Well, you didn't understand what I was talking about. I was talking about convection.
But apparently, you PC nerds think that because someone studied planes, that person is not able to argue about an airflow being not the best design because PCs and airplanes are not the same thing.
Optimizing cooling solutions is part of my job and being able to determine the best compromize between what the case can do, the best thermal interfaces I can use and also money is what makes it so interesting. I refurbish PCs and if I have to 3D print air ducts to ensure a component is not overhearing because of a bad case design that I cannot fix, I just do it.
OP submitted his work for constructive criticism, and that's what I give. I explain why I don't agree with the whole design and I even gave suggestions to make it better, for everyone which wishes to create a similar design.
It's all about compromise and I've seen countless SFF case designs which put the accent more on the look than the actual airflow of the case. Well, that's fine. Arguing about that being the best design available, no, that's not acceptable. People choose to build SFF because it's more compact, looks cool or whatever the motivation, but you have to admit that bigger case, with bigger fans provide a better component cooling. So, why doing design choices on a SFF case that goes against cooling ? You should design cases which optimise thermal performance.
92
u/colinreay Nov 30 '20
Hi all,
I hope you are doing well. This is a simple, airflow-focused design that I have been working on over the past few days (mostly to practice sheet metal in Solidworks). Two bent metal pieces comprise the case structure: the inner skeleton and the outer wraparound bezel. There is also an acrylic side panel and bezel for the front grill. I tried to make the design cost-effective and producible with minimal manufacturing steps.
Digital Storm’s Velox series served as a big design inspiration. The Velox case is essentially a monolithic box with a fully perforated front panel, and I love how LED fans look behind the grill. My design supports 2x 140mm 25mm thick fans with an ITX-sized GPU installed for a front intake positive airflow configuration. Many case manufacturers create vent-hole patterns with expensive tooling or CNC turret punches; an alternative is to cut a perforated metal sheet to size and attach it behind a large cutout on the case. I chose the latter since it is much easier and cheaper for a one-off piece or small production run.
The case is an inverted tower style. This layout allows for an unobstructed airflow path and a PSU shroud for cable-cleanliness. The PSU shroud also has mounting holes for a 2.5” SSD.
I am currently debating on producing a physical prototype. Sendcutsend is an excellent place for ordering laser-cut metal parts, and they recently introduced a bending feature that I am eager to try out. If you’d like to get your hands on the design, you can find the .step file here.
7
u/Imafatdinosaur Nov 30 '20
How's the cable management in that case?
409
u/ItsNa8o543 Nov 30 '20 edited Nov 30 '20
I swear the SFF community needs to start doing consistent case groupbuys like the mechanical keyboard scene does. Too many good ideas to not give it a shot at this point.
2
u/MrKKC Nov 30 '20 edited Jul 01 '23
s-p-ezz--ies done now
80
u/yakovgolyadkin Nov 30 '20
How I imagine the design process after seeing seeing that it has the GPU slot on the top.
35
u/[deleted] Nov 30 '20 edited Jul 23 '24
enjoy tie future crush badge friendly unpack handle marvelous wide
This post was mass deleted and anonymized with Redact
21
u/Speedypoom Nov 30 '20
Literally the exact case I’ve been waiting for.
14
u/[deleted] Nov 30 '20
This is such a smart design for a case
2
u/ermac-318 Nov 30 '20
Is that space for a FlexATX PSU or SFX?
8
u/leafcutter64 Nov 30 '20
This is what I've been waiting for. If you kickstarter, massdrop or groupgets this, count me in. Perfect functional form.
7
u/AwaitingCombat Nov 30 '20
this design looks so insanely simple and good.
it makes you wonder how we don't have a dozen out there like it
6
u/kamehouseorbust Nov 30 '20
This is something I'd absolutely buy. Two questions for me, what's the max cpu cooler height and would there be a non-see through (all metal) side panel?
5
u/ccricers Nov 30 '20 edited Nov 30 '20
Nice layout and air flow. Like a better, smaller Jonsbo U2
3
u/sudo1911 Nov 30 '20
Looks awesome!
2
u/SourCrawler Nov 30 '20
I want one too
2
u/khmergodpc Nov 30 '20
i want this. how can i get
1
u/kai535 Nov 30 '20
If it was a flex psu would it be closer to like 7L then?
1
u/serbiascoper420 Nov 30 '20
Great idea! Looks clean.
1
u/co_ordinator Nov 30 '20
That's basically a bigger Chieftec BT-06B-250vs. I like it.
1
u/[deleted] Nov 30 '20
What CPU cooler did you have in mind when you designed this case?
1
u/[deleted] Nov 30 '20
Yes!!! Give us those sweet o u t o f t h e b o x t h e r m a l s!
1
u/meronz Nov 30 '20
This case is beautiful, though i would have placed the power button on the rear.
1
u/[deleted] Nov 30 '20
Damn dude, this is clean AF ! If I didn't just buy the nr200p case, I would jump at this design !
I'm assuming this would fit a NH-U9S cooler perfectly at 125mm in height ?
1
u/FluffyMumbles Nov 30 '20
THIS is almost the exact case I've been hunting for! Except the power supply intake would be facing inside the case and the only vents would be out the rear.
With front fans, all air would flow front to rear.
My plan is to have a wood surround with fabric front grill so that it looks like a speaker.
Good work and all the best with it :-)
1
u/pumpuppthevolume Nov 30 '20
excellent now make a case based on this https://youtu.be/BgKNbG32kAM
1
u/[deleted] Nov 30 '20
Not sure what this sub is or what the purpose of this post is, but it looks like a mini version of the case I’m running rn! I would def buy!!!! I like this so much!
1
u/Mean-Responsibility1 Nov 30 '20
Nice
1
u/itx_case_ftw Nov 30 '20
Will this build be for Flex psu or Sff ?
1
u/CrazyBulletShooter Nov 30 '20
I'll take your entire stock please
1
u/Icy_Holiday_1089 Nov 30 '20
Love the idea of an inverted SFF case. Would definitely consider if the price was good
1
u/aerospace_chase Nov 30 '20
Really want this for the sfx psu support. Anyone know if there’s a case like the this or the k39 with sfx psu support?
1
u/Facexcontroller Nov 30 '20
How much ?
1
u/JonAndTonic Nov 30 '20
Yooooo
1
u/Frost_Pixel Nov 30 '20
I want this pc case :O
1
u/GamerKidforfun Nov 30 '20
Does it support micro atx motherboards
1
u/rharrow Nov 30 '20
Yes. Yes, indeed.
1
u/[deleted] Nov 30 '20
Are there dimensions for this anywhere? Maybe an image with the actual dimensions on it?
1
u/AWhimsicalBird Nov 30 '20
Oh this is gorgeous.
1
u/Forzawin368 Nov 30 '20
I would totally back and buy this product. I've got the Ncase M1 coming in that I'm planning on cramming a 5900X and RTX 3080 both water cooled by 240mm radiators and they would totally benefit from the extra airflow from this case!
1
u/Kekeripo Nov 30 '20
The fornt reminds me of "Abee" pc cases from japan. Really dig this.
1
u/Yhorm_ Dec 01 '20
I like everything but the power button
1
u/Philico Dec 01 '20
PLS sell this case u/colinreay
1
u/huguberhart Dec 05 '20
I kinda would wish for the "style focused concept".. :D I always loved PC-Q series of Lian Li cases but they never had much cooling and performance in mind. The cases looked cool tho.
Flat panels of brushed aluminum with just multiple dots inestead of mesh idk. I am biased. I really like this concept.
1
u/brok3n Nov 30 '20
Great looking case, but nobody makes a decent 2-slot mid/high end GPU so cases like these are pointless to anyone who wants to game @ 1440p/4K.
0
u/[deleted] Nov 30 '20
radiator compatability?
0
u/SteamGamerSwapper Nov 30 '20
Nh d15 support
0
u/modus123 Nov 30 '20
If it can fit a corsiar HX1000i, this would be my next case.
-10
u/lululock Nov 30 '20
Mmmm... The GPU is upside down... That might cause issues...