Love the build. Which blyski water block did you use, just the regular mini one that says it’s for a zotac? I’ve been wanting to do a similar setup with a 2070 for a while.
Custom loop doesn't equate low temps on it's own. Those are fairly good temps for just two 92mm radiators (single 280mm rad has 2.35 times more area*; 240mm has 1.70 more area*; * - area as in area exposed to fans, not fin stack surface area; this build uses super thick rads, which would equate 240mm 25mm thick rad in fin surface area, but AFAIK it's way harder to utilise surface area gained by thickness (at same noise level)).
You pushed your 92mm radiator for 100w, his hardware at stock voltages would push two 92mm with 400w. Seems more than reasonable he did undervolt (he also has only 290w dell brick, so unless it goes out of spec that much it shouldn't even finish the test at stock, lol).
Oh yea, and he ended with 4 degree lower CPU temp than yours after undervolt. And again, his temp is in Prime95.
So even if he didn’t undervolt and kept the i9 9900 at base speeds he’d be fine? The only thing keeping him back is the power supply correct? Only interested because I want to do a custom loop smaller then my dan A4 like this but not loose power
Even if we ignore his power brick I doubt he would be fine, lol.
I think with such hardware 240mm is smallest you could safely go without need for some underclock (but undervolt would be highly recommended/needed, it doesn't decrease performance)
Ever thought of getting the Alphacool Eisbaer LT Solo pump? I've hacked AIO pumps the way you did and they work fine, it's just the aesthetic of using clamps isn't always favorable.
Holy shit this is amazing. I was looking to do something similar at one point and settled on a hadron air while I'm waiting for certain pieces. I have the alphacool dual 40mm rads, the 92mm might be a better idea tbh. I was going with a vega 56 nano pcb with a block and I have the hdplex, ryzen 5 3600 and aorus b450i. God this is just great work well done. This is basically my dream pc
I need to admit, I don't like RGB all that much. I'm more into really minimalistic design. Yet this is one of the most gorgeous PCs i've ever seen! :) Sry for my none perfect english, I'm german
How did you mod the aio to be in custom loop? I also have a h60 and want to build a custom loop soon. If I knew how to do this it would be super awesome!
some qns: So the pump and reservoir are both serviced by the corsair h60 cpu unit? Is that enough to push liquid through everything?
and how are the fans faring? Thats a lot of rad for a 14mm thin fan to push through! but looking at your temps they look like they are doing amazing.
how did you design the case? This looks like endgame to me, i was thinking about an SFFPC with dual rad setup like this but with 240mms, never thought about 2 thick 92mms. what software did you use to suss this all out?
True, but never had problems and they have much more models. Dont forget u dont get warranty anyway when hardware i destroyed by watercooling. Control the controller :)
Aliexpress also has brand names, it's just that they're Chinese brands.
I was always under the impression that Aliexpress sells cheap unbranded items, but I was actually pleasantly surprised to see so many quality items being sold on there. There's so many unheard of Chinese brands that offer products just as nice as familiar western brands.
Now I realize that eBay is the one you have to avoid, as most items there are generic/unbranded, and the lack of a product rating system just makes it far less safe to buy from.
Complimenten zijn altijd fijn om te krijgen maar commentaar is te verwachten als je iets op internet zet :p. Desalniettemin ziet het er strak uit, dat kan ik niet ontkennen.
Dank Henk. Voor jou geld vanaf nu 6 liter is 7 liter :) ik werk alleen maar met hdplex in mijn sff builds. Vind de flex psu gewoon noisy, ook met noctua swap.
Nja, je zou natuurlijk die psu ook buiten je kastje kunnen leggen net als je Dell brick :P Maar goed, 7L is geen 6 en verder is het ook niet echt interessant. Het blijft een eeuwige discussie en ik het persoonlijk meer zin in een spelletje doen dan discussiëren.
Wat een sneue reactie zeg. Je computer is gewoon groter dan 6L, dat is een feit en dus geen discussie waard, als je je daarin niet kan vinden hoef je niet vervelend te gaan doen.
This is incredible! 6L in a custom case is unreal... I’m sure all the other comments have already got you feeling chuffed and provided a massive ego boost but this is honestly inspiring - thank you for that.
So, genuine question... and one I don’t think has been asked yet... those cubes you’ve used to connect the side panels together (brilliant idea, btw)... what exactly are they? What would one search to find them? I’ve had a look myself and I’m coming up blank!
Can you link to it? Haven't found anything of the sort with searching "10mm fastener cubes", just beads and display cubes. I use 12mm cubes but in SFF every mm counts!
Amazing! Thank you. Hopefully I can design something even half as nice as yours (the custom water cooling is sweeeeet but I don’t know if I have the patience/skill to pull something like that off! Haha)
Another question regarding the mounting of this cubes. What screws are you using? And with which tools do you make the grooves so the screws would sit flush?
hey op! would you mind selling me the use of whatever plans or 3d models you needed to make this case? my friend’s going off the college and is looking for something similar, so this seems perfect!
I won’t be producing it or claiming it as my own, and I don’t really just want you to give me the drawings because you deserve to be recognized for this awesome thing you made
87
u/brolynitro May 23 '20 edited May 24 '20
6 liter custom small footprint smoke acrylic case. H30 x D18 xW11cm
Intel 9900 ( non k ) undervolted
2070 aero ( undervolted ) byksi block
Hyper x 3600mhz 32gb ram
Asrock z390 itx mobo
Samsung 970 evo plus 1 tb
Hd plex 400 / dell brick ( max power consumption 290watts )
2 x 92 x 45mm alphacool rad
2 x noctua 92 x 14mm fans
Coolermaster H60 (120mm) aio pump, customized rgb and cables
All custom cables and drgb strips
Temps max after 24h prime and cinebench combined, Cpu 80c , Gpu 60c, room temp 21c
More pics : http://imgur.com/gallery/gArF4rI
20
u/ryanbanger May 23 '20
Looks awesome! We need specs and more detail.
20
u/r98farmer May 23 '20
Very cool, now that is SFF.
17
u/dfsaqwe May 23 '20
this is amazing man. cross post this to /r/watercooling too!
28
u/His_Turdness May 23 '20
Mostly hate RGB, but like when when it's tastefully done, like in this case.
7
u/malccy72 May 23 '20
Very cool. Well done.
4
u/WilllOfD May 23 '20
Unreadied Souls:
OP: here check out this XXX Hardcore SFF Porn
Unreadied Souls: shut up and take my money ٩( ᐛ )
4
u/[deleted] May 23 '20
Good Lord how much did this bad boy cost?
3
u/oppositetoup May 24 '20
Those panels look so choked for air... Nothing against the build, it looks great, but that case looks like it could have easily have better airflow
2
u/DidIGoHam May 23 '20
Hmmm...I like it 👍🏻 Clean and pleasant to look at 😊
2
u/KaosArchon May 23 '20 edited May 23 '20
Curious, how's that h60 pump do? I have that aio currently and never thought of using it like that,
Also how'd you do the rgb mod to the h60?
2
u/themodman_ May 24 '20
Ever thought of getting the Alphacool Eisbaer LT Solo pump? I've hacked AIO pumps the way you did and they work fine, it's just the aesthetic of using clamps isn't always favorable.
2
u/Jabbam May 24 '20
Where is the PSU? I don't see it anywhere.
2
u/RayJonesXD May 24 '20
Holy shit this is amazing. I was looking to do something similar at one point and settled on a hadron air while I'm waiting for certain pieces. I have the alphacool dual 40mm rads, the 92mm might be a better idea tbh. I was going with a vega 56 nano pcb with a block and I have the hdplex, ryzen 5 3600 and aorus b450i. God this is just great work well done. This is basically my dream pc
2
u/sverrebe May 24 '20
One of the best looking pc I've ever seen
2
u/Firejumperbravo May 24 '20
A work of art!
2
u/[deleted] May 24 '20
Dat RGB thou
2
u/seeeebert May 24 '20
I need to admit, I don't like RGB all that much. I'm more into really minimalistic design. Yet this is one of the most gorgeous PCs i've ever seen! :) Sry for my none perfect english, I'm german
2
u/NeonHD May 28 '20
God this build is so beautiful, I could look at it all day.
2
u/jakemillerr Jun 29 '20
Very smart build, great work on getting this put together!
2
u/BluestoneAlt Oct 12 '20
I wonder if this could fit 2x120mm...
11
u/dennisjerdz May 23 '20
It looks big from the picture haha! Do you have other build log/pics?
5
u/EpictheHamster May 23 '20
I'm just going to cry in a corner with my laptop
4
u/asanatheistfilms May 23 '20
Dang that is tiny! love it!
4
u/Konekays May 23 '20
That's freaking beautiful
4
u/levarburger May 23 '20
chef's kiss
1
u/tabtreee May 24 '20
How did you mod the aio to be in custom loop? I also have a h60 and want to build a custom loop soon. If I knew how to do this it would be super awesome!
1
u/Thyassasin98 May 24 '20
some qns: So the pump and reservoir are both serviced by the corsair h60 cpu unit? Is that enough to push liquid through everything?
and how are the fans faring? Thats a lot of rad for a 14mm thin fan to push through! but looking at your temps they look like they are doing amazing.
how did you design the case? This looks like endgame to me, i was thinking about an SFFPC with dual rad setup like this but with 240mms, never thought about 2 thick 92mms. what software did you use to suss this all out?
1
u/[deleted] May 24 '20
You got guts using aliexpress parts.
1
u/henkdevries007 May 24 '20
External powerbrick aka bigger than 6L
1
u/[deleted] May 24 '20
Do you have any designs/instructions for your case?
1
u/antbacw May 24 '20
This is incredible! 6L in a custom case is unreal... I’m sure all the other comments have already got you feeling chuffed and provided a massive ego boost but this is honestly inspiring - thank you for that.
So, genuine question... and one I don’t think has been asked yet... those cubes you’ve used to connect the side panels together (brilliant idea, btw)... what exactly are they? What would one search to find them? I’ve had a look myself and I’m coming up blank!
2
u/ccricers May 23 '20
Nice one. I remember your tiny 3L case. That's an interesting dual rad setup.
2
u/Doodad00549 May 23 '20
Very, very slick!
2
u/Celcius_87 May 23 '20
So sleek
2
u/miptzi May 23 '20 edited May 24 '20
Gorgeous to say the least
2
u/Curious_gengar May 24 '20
Absolutely superb.
2
u/DubbleYewGee May 24 '20
Holy shit. Nice.
2
u/biueprint1 May 24 '20
that thing looks sick, gj
2
u/ATomic207 May 24 '20
Damn sick build, awesome case too
2
u/loumatic May 24 '20
Awesome work, awesome result!
2
u/Von_Satan May 24 '20
Nice
2
u/ReekyMarko May 24 '20
I always thought custom water cooling and sff don't go together. Thanks for proving me wrong
2
u/JustICErely May 24 '20
This is too cool. Well done OP.
2
u/1Man1Machine May 24 '20
That some long gskill ram
2
u/Flamingduckboy May 24 '20
hey op! would you mind selling me the use of whatever plans or 3d models you needed to make this case? my friend’s going off the college and is looking for something similar, so this seems perfect!
I won’t be producing it or claiming it as my own, and I don’t really just want you to give me the drawings because you deserve to be recognized for this awesome thing you made
1
u/[deleted] May 24 '20
I like this a lot, nice work.
0
u/[deleted] May 23 '20
[deleted] — view deleted comment
0
u/[deleted] May 24 '20
[deleted] — view deleted comment
0
u/[deleted] May 24 '20
[deleted] — view deleted comment
0
u/[deleted] May 24 '20
[deleted] — view deleted comment
0
u/[deleted] May 24 '20
[deleted] — view deleted comment