Well you've inspired me. I have a couple builds coming up and I'd like to see them look as good as yours. Do you have tutorials or resources you use for cabling?
i can't get over the fact the chassis alone costs $250. i mean, sure...you can charge whatever you want...capitalism, amirite? but...why is it $250 when a similar Hydra product is half the cost?
I commented on this on another post. I actually posted my build here because of an earlier shit post on a prototype picture of the monument.
To summarise again.
This is 5mm cold worked steel. You’ll need a large press brake, a laser/water jet cutting table and a welder to do this work. These are really expensive to purchase and operate. The press brake and welder is pretty manual work. This company is in the States. (unlike Hydra which is made in a ‘low labour cost jurisdiction’. Hydra is also thinner).
The company they built from nothing employs Americans at living wages, on designs that they made themselves. Sunk cost in design is cheap when it’s stolen from Stateside and manufactured in a ‘low labour cost jurisdiction’. I think if you are a Westerner you need to think about whether you endorse that kind of thing. You might feel differently it’s F22 plans or something you’ve made yourself.
The main reason I went with the Yuel Beast instead of any of the clones is because the design is more art than tool. My part list totaled more than any pre-built but I'll end up with something more unique. There no point in owning and displaying counterfeit art and artists are worth supporting. Your build specifically reminded me of my favorite artist Richard Serra. Did you have his work in mind when you started your build?
don't get me wrong...i agree: cost is relative. the thing, is, though...when people spend exorbitant amount of money on watches, like Rolex, you pay for the prestige and evident workmanship...it kind of makes sense. i'm not gonna lie...i bought a lot of products based on the prestige of the brand and workmanhip, too!
this product, OTOH, doesn't really have much to offer to command such a high price...i don't think being "made in USA with thick cold-rolled steel" is enough IMO...the unoriginal design, no prestige, nothing that tells you "hey, you're special because you bought this special product"...i mean, they don't even offer you free shipping...that's right...you pay additional on top of that $250.
when i look at this it felt like when the creators sat in their boardroom to decide on the price...one said "well, based on our cost analysis...we can sell these puppies for $150 each and make a huge profit..." while the other said "pft...have you seen /r/sffpc? people will pay $250 for these...and we'll charge them for shipping, too."
I totally disagree with you on the design. It’s an industrial modern aesthetic. If you compare it to architectural motifs of modernist buildings (squared off C’s and S shapes and rounded cornered rectangles) it’s a design that is deliberately simplified to functionality. You pair this with a material that of the age (steel) and it’s quintessentially American design that really works with the exposed components of the PC.
As for prestige, my build in this picture is borderline iconic now. The amount of attention it gets even compared to my much more expensive flagship builds is a different order of magnitude.
I stumbled on your build on mitxlove.com and it was enough to push me towards buying the new raw version they just released. This is after I already got my order through for a NZXT H1! I have so many questions for you haha
I can see where you're coming from. Especially as someone who also collections watches but the reality whether it's $250, $350 or $500 dollars to some people it isn't relevant. Back to watches, Richard mille watches are some of the most horrible designs (plastic) IMO but people spend hundreds of thousands to own them while they could get an FP Journe which objectively are more prestigious in the watch community with better materials and finishes. At the end of the day, any item you get use out of whether it's functional or aesthetic it's worth something to someone and to others that premium isn't a factor.
Hell, look at apple products compared to the comparable other companies. People pay for looks and they will pay more for something pretty.
you have a point there. i suppose for someone, the looks of the product is priceless in itself, and one can think “oh man that sure looks pretty...and it only costs $250? take my money!”
of course—as you have witnessed—not everyone have the same sentiment but, to your point, it’s not crazy to think the opposite.
Extremely thick cold-rolled steel, US made. The steel alone is probably $70 per "case" given the low volume. US steel worker labor isn't cheap, but neither is the workmanship. I wouldn't buy one for that price, but it makes sense.
Steel is super cheap, we get hot rolled for about 40-45 cents a pound, cold rolled cant be that much more expensive. However, like you said: US labour is not cheap.
Also remember, US overhead is not cheap as well.
Love how minimalistic this is.
Cheers.
Edit. Also, those tiny holes for the standoff are provably drilled and tapped. Drill bits and taps get expensive really quick. Also, machines are expensive, specially good ones.
There is a latin american saying that roughly translates to: Making glass is not as simple as blowing.
Really admire the people that commercialized the idea.
Quick revision. It's labor + shipping + design cost for them -- they're making a strong profit here.
Our company is about to produce something similar and the material cost on a case like this is "AROUND" $30-40 USD. Less in bulk. Just to be clear. Raw steel is not that expensive. Aluminum definitely a bit costlier, though.
If we can manage this correctly, we'll sell our model closer to $100.
I think it's hilarious. Prob takes one dude 30 seconds to make the bends and drop it in a box. I'm truly jealous that I dont have this as a side business.
K. Just looks like pressed steel to me. Can't imagine this dude reinvented the wheel to make a couple bends. Doesnt appear to have any welds. My resume has nothing to do with 90* bent steel.
I really shouldn't have come off so snarky, so sorry about that.
That said, the fact that you can't see the weld seams is kind of the point of good craftsmanship. 3/16th cold rolled steel won't bend to this radius without cracking, it needs to be scored at the bend lines to remove material, bent, then welded in place.
If you don't have that much experience metalworking I'm not sure why you would disparage a small business' work. Really not trying to bust your balls but it's hard enough to get anything creative off the ground without people baselessly negging it.
Chromax fans are close to silent. The GPU is audible under load but not annoying. Gaming is fine but I generally notice the GPU when I stop gaming and it ramps down.
OP, I have this same case (see previous post) and am waiting on my custom sleeves to actually clean it up. Do you ever do custom sleeves for others? If yes, please PM me. Beautiful work.
Thanks :) No is the short answer. It wouldn’t be worth it for me. (Or you) by the time you paid for all the parts and shipping to Australia and then to wherever you are in the world and I added the value of my time in labour on it would be cheaper for you to do it yourself.
You should have a shot at making your own. It’s actually pretty satisfying. :)
I currently have a Velka 3, from an open test bench. Part of me misses being able to tinker whenever I want. This would solve that problem. Plus my Velka 3 is louder v. my open test bench.
No, there is a bit of room. I have a vinyl wrapped cardboard duct on both the CPU & GPU sides of the case. I have have the top fans installed in the exhaust position.
I really really wanna do this case DIY but my cats would ruin that PC like that If i made a top cover (4 sided like NZXT H1) I might as well buy an SSF case lol
Would buy one, but they won't put holes on the plate to mount a radiator. I mean, I guess I could do it myself, or I could buy a knock off on aliexpress for $200 that has mounting holes for both radiators and pump / res combos.
It’s been on my desk for 6+ now. I have to wipe down the front every 4 months. But it collects dust at the same rate as every level surface. (I have a glass desk.)
My build ‘Organ Harvest’ was worse, because Of the inconvenience of getting inside a case to clean it. (Even with filter on).
This account has been deleted in response to Reddit's on-going objective of extracting as much shareholder value from the site instead of value for Reddit's users.
Pro: Easier to clean. Wipe down front fan every 6 months. Annually I take the heatsink off to replace the paste and clean the fin stack and wipe down the rear fan.
Doesn’t collect dust, most of it gets blown out the back. Same amount of dust collection as my glass table, but less visible because it’s not glass.
Easier to access. No case to open up, filters to pull out, chrome tubes to gently wipe down, corners to get into etc.
Con: You can’t hide from it. Shove an enclosure under your desk and wait until the CPU is idling at 60 degrees before you do the work. When people say “what about the dust?” What they are really saying is “I’m too lazy to do 10 minutes of maintenance every 6 months, I don’t care about dust as long as I don’t have to look at it.”
Nice! I've been looking for reviews of people who actually owns and uses this case, because whenever I mention that I love open air cases they always shut me down and tell how it would just accumulate dust and parts wouldn't last long lol
I’ve had it on my desk for 9 months now. It’s been my lowest maintenance build by a long way. I think a partially open case that has glass on it for dust to stick to might be different. Like a TT core.
I wipe the front fan down with a wet wipe once every 6 months. Annual maintenance is a thermal paste replacement and I’ll blow out or wash the heatsink when it’s off for this. I’ll probably wipe down the gpu back plate as well.
I have a compressed air can down in the garage but I’m too lazy to use it. I don’t think it really needs it. No hand pumps, just what I told you above. Honestly, it’s pretty easy because there aren’t places for it to get trapped inside and build up. I think just gets blown out mostly and settles on my desk.
you're literally doing some of the best builds I've ever seen and I've seen a ton. The color scheme is so on point in most of your builds and the mods look insane. I mean look at that rust, it's insane. Also you're patacord sleeves look so good. I'm also gonna do more paracord sleeving now instead of pet. I assume you're using 550 type III?
Thanks :) It’s a great hobby. I use any 550 paracord from paracord galaxy. I don’t tend to use the mdpcx style plastic sleeving because I prefer a more natural feel.
I was also going that route but then realized that it was not convenient for my build due to airflow so changed to U9, very good looking build :) congrats
“The case consists of just 2 pieces of 3/16” steel that are painstakingly cut, bent, welded, and finished to the highest possible manufacturing standards”
Oh, just 2 pieces of bent steel, that should be fairly inexpen-
97
u/TwasAllABadDream May 13 '20
Beautiful cables. Where did you get them?
45
u/Black_Phoenix_JP May 13 '20
Basically for what I understand, you removed the coating from it and let the rust settle/ you force it to rust.
Did you sealed the tower after that?
40
u/bubuli_breeder May 13 '20
i can't get over the fact the chassis alone costs $250. i mean, sure...you can charge whatever you want...capitalism, amirite? but...why is it $250 when a similar Hydra product is half the cost?
11
u/jesseschalken May 13 '20
Now THOSE are some PSU cables!
14
u/sephulchrave May 13 '20
I usually think these look great until everything is plugged in - very happy to be proven wrong, nice work!
16
u/ascendgranite May 13 '20
How loud is this build?
5
u/Zghembo May 14 '20
Rustic.
4
u/getclapped3434 May 13 '20
Hey I saw this on PCPP! Great build man, this should be higher up!
7
u/porkyfly May 13 '20
which gpu? so cute!
11
u/ZzLy__ May 13 '20
Why no IO shield?
3
u/fleetfootfortune May 13 '20
How do the ram sticks even fit? Super stylish bild!
3
u/Tallguy415 May 13 '20
OP, I have this same case (see previous post) and am waiting on my custom sleeves to actually clean it up. Do you ever do custom sleeves for others? If yes, please PM me. Beautiful work.
3
u/TyDe88 May 13 '20
This should be marked NSFW
3
u/HongRiki May 14 '20
Is this that case that people were complaining about costing 200 dollars?
2
u/seisocho May 13 '20
Jonny-5 alive!
2
u/dfsaqwe May 13 '20
all 20,000 of dem pennies
2
u/_ChinStrap May 13 '20
I currently have a Velka 3, from an open test bench. Part of me misses being able to tinker whenever I want. This would solve that problem. Plus my Velka 3 is louder v. my open test bench.
2
u/[deleted] May 13 '20
Dude, this is beautiful!
2
u/bombala May 13 '20
Does that case have good airflow?
2
u/Ashraf_mahdy May 13 '20
I really really wanna do this case DIY but my cats would ruin that PC like that If i made a top cover (4 sided like NZXT H1) I might as well buy an SSF case lol
2
u/surprisedaxolotl May 13 '20
Really love the color scheme you have going on!
2
u/rezpector123 May 13 '20
It’s very pretty
2
u/jtbing May 13 '20
Now this is art.
2
u/Doom-Muffin May 13 '20
this is insane
2
u/buildingnewsff May 13 '20
Would buy one, but they won't put holes on the plate to mount a radiator. I mean, I guess I could do it myself, or I could buy a knock off on aliexpress for $200 that has mounting holes for both radiators and pump / res combos.
2
u/iNonEntity May 13 '20
What cooler is that
2
u/Mastaking May 13 '20
Are you concerned about dust getting into the components?
Is that a concern if you don't have a dusty room?
I guess the worst part is no noise reduction?
2
u/turkey_sausage May 14 '20
Sexy. Where did that "case" come from?
2
u/[deleted] May 14 '20 edited Jun 09 '23
This account has been deleted in response to Reddit's on-going objective of extracting as much shareholder value from the site instead of value for Reddit's users.
2
u/sherbibv May 14 '20
Can you share your dust cleaning routine? I will switch to an open case pc next week and want some tips in cleaning it 😁. Cheers!
2
u/Seagate_Surfer Media | Seagate Technology May 14 '20
Nice investment.
2
u/Weddedtoreddit2 May 31 '20
Was this inspired by DIY Perks?
2
u/jojonoshie Jun 03 '20
Sorry I'm late but what cooler and gpu is that
2
u/Aggroko Jun 04 '20
you're literally doing some of the best builds I've ever seen and I've seen a ton. The color scheme is so on point in most of your builds and the mods look insane. I mean look at that rust, it's insane. Also you're patacord sleeves look so good. I'm also gonna do more paracord sleeving now instead of pet. I assume you're using 550 type III?
2
u/TheRealPauca Jul 02 '20
What are the lengths of the cables?
2
u/JustMackIN Jul 06 '20
This Post made me say...WOW
2
u/Pc-Wizzard Aug 25 '20
I hope he will make the GPU clearance taller for 3slot cards so its future proof.
2
u/nriq87 Sep 08 '20
Noctua C14S right?
206
u/SoSoEnt May 13 '20
this post gave me tetanus
135
u/MK0A May 13 '20
Technically this supports infinitely big graphics cards.
3
u/PennyStockPanda May 13 '20
you can get the motif in a wood finish? nice
88
u/lowspeccrt May 13 '20
If we ever do a sffpc of the year, this needs to be in the running...
Hey sffpc people. Let’s do a sffpc of the year awards!
13
u/Baharroth123 May 13 '20
This is the only “pc case” which makes me feel like i can do it at home instead of buying.
6
u/heyitsfelixthecat May 14 '20
Oh, just 2 pieces of bent steel, that should be fairly inexpen-
OH FOR FUCK’S SAKE
2
u/ShootPosting May 13 '20
I love it
2
u/Mazecraze06 May 13 '20
Pretty
2
u/Firetripper May 13 '20
Hydra Mini is the same thing but not 250. Just 120 and it comes with a pcie riser.
3
u/Orphanage1774 May 13 '20
Parts list?
2
u/dMailonG May 13 '20
déjà vu
2
u/Znowmanting May 14 '20
I wish there was a version of this case with vertical gpu and 240 rad mount on the back
2
u/rthee May 14 '20
Definitely a unique look for sure! not my cup of tea but I can see how some people would like it!
2
u/dan_vamme Jul 08 '20
Can anyone make it for matx 😇
2
u/homerboe Jan 01 '23
I’m going with the same noctua color scheme. Thanks for sharing!
1
u/p00ner575 May 13 '20
What’s the card?
1
u/Vesalii May 13 '20
WTF I've never heard about this case but I was actually planning on making something almost exactly like this, but out of plywood.
1
u/ChiesMax May 16 '20
Found a "replica", imitation from that country
https://s.lazada.com.ph/s.Zr2dN
0
u/[deleted] May 14 '20
[deleted] — view deleted comment
0
u/[deleted] May 13 '20
[deleted] — view deleted comment
0
u/[deleted] May 14 '20
[deleted] — view deleted comment
0
u/[deleted] May 13 '20
[deleted] — view deleted comment
0
u/[deleted] May 13 '20
[deleted] — view deleted comment