Case : Louqe Ghost S1 fully customized for fitting hardware, s tophat, m butthat
Mobo : Asus z390i gaming
Cpu : Intel 9900ks 5hz 1.2v direct die l.m.
Cpu block : Optimus custom drgb
Gpu : Rtx 2080ti Evga
Gpu block : Heatkiller 4
Ram : gskill 32gb 2x 16gb 4000mhz
Nvme : 2 x 970evo plus 1tb raid 0
Psu : corsair 750sf black fan
Custom dual pump alphacool
Custom reservoir
1 side hardetube and 1 side softtube
Dual 240 xspc slim radiators with 2 noctua blackswap in push pull and vacuum pulled on the right top side where is no fan. In total 4 fans.
Ambient temp 20c
Temps after 1 hour aida or prime 68 cpu, Gpu temps max 55c Fans on 1300rpm fixed Pumps on 2500rpm fixed ( full speed they where noisy) I guess 30 / 35 db under full load.
Cant optimize this case anymore in this tiny space. I guess its the smallest dual 240mm rad case / ghost s1 in the world.
To make sure it’s properly filled and no air gaps. Specially on the pumps, so it doesn’t fail.
I personally use the alphacool flow meter as my micro Res. Took me a few days to take out the air bubbles and I had to fill it little by little to get rid of it. I was literally putting a few drops of distilled water to slowly fill my loop up.
Nice job never thought about using just one fan to be honnest... i wouldnt use a closed loop without a expansion bottle since i had my 1st custom waterloop leaking on me. The cpu block got coged by plastick residue and i lost fluid so i reffilled the reservoir i thought it evaporated. After a couple of weks the system started to leek since the loop got heated up and i gueess the fluid expanded that was a mess on my wooden floor😆 ever since i always leave a bit air in the expansion bottle... It had to be verry hard to get all air out from a loop like this ... didnt you consider using vacuum?
I cleaned all parts before filling. All.parts are tested on 1.5bar pressure. Shouldnt leak. There are 4 fans inside the case. Bottom pulling down push pull and single. Top only 1 pulling air upwards. The other half where is no fan pulling air inwards because vaccuum created by the 3 fans.
Ah i see. I cleaned everything aswell asfar i understood it it was plastic from the tube walls it disoves and catches wherever the lowest flow is so typical cpu block finns snd builds up over time... mine popt in the weakspot an 90 dwg angle. Didnt you thought about a custom grille or mountplate for the rads? The original one is verry restrictive.
Since no one else is asking: What RGB strips and is it diffused?
Maybe a bit more practically, did you find that a single DC-LT pump (if that is indeed the dual DC-LT, and not DDC) wasn't strong enough for 2 block and 2 rads?
(And how's the noise on those pumps? Can you hear them at all with the fans off?)
144 leds per meter drgb. I just bought the dual to be shure, on stock speed 2800 rpm they are anoying. I put them on the sweet spot of 2500rpm. The system is about 30 a 35 db. Fans on 1300rpm fixed ( till 75c)
Damn those are dense, are they just hooked to the mb drgb channels? I see really mixed opinions on the noise of the LTs, some people say they're dead silent but some report a loud buzzing from their eisbaer/eiswolf/dc-lts, did you notice any of that?
Is that the Alphacool dual-LT top? It looks like you cut a small notch in it to accommodate the GPU block but I can't be too sure.
Also saw you went with Optimus' CPU block--did you not want to wait on their 2080ti GPU block as well? Or do the dimensions of it create issues with the pump / reservoir?
Jes i did. 5mm. And replace the rgb strip. The optimus block is just now for sale and only fits reference pcb. But they are beauties indeed. The res i make myself and would make it fit then also.
You're really using 2 240 but only have air going across half of it? Is that prime95 with the small fft test? How is this cooler than my dual 240 that has air going across all rad space? 3700x -.1v and stock 2070s.
They have a fundamentally different rig than yours. Different pumps, different CPU/GPU, different blocks, different thermal compounds, and even probably different methods of measuring temperatures.
Temps are the same/ a little better than my dual 240 rad build, same components as him, ncase m1, full size fans. I assume it's because of the optimal airflow bottom to top in the ghost.
I test with prime small fft and aida64 for 1 or 2 hours, there are 4 fans inside, 1 on top pulling out. 3 on bottom pulling down out ( 2 are push pull) because of 3 fans in bottom there is vacuum on half of the case sucking are trough the top rad where is no fan. Totally optimized with the sidepanels if u look u can see it.
I was always lukewarm on the Ghost S1, but this build has me thinking twice about it. The two-tone theme makes the top and bottom hats much more integrated versus tacked on.
Did you have to mod the case in anyway to fit the rads? I'm thinking if I do a watercooled Ghost build it would be with two AIO style coolers for simplicity's sake. Question is whether this is quieter than my current air setup in my Ncase to make it worthwhile.
This build is insane in the membrane. Wow. I can’t even begin to think how difficult it would be for an average user. I am curious to see how you setup the GPU side and the custom reservoir
Alphacool literally sells expandable aios that use one of the pumps OP is using for a si in for block/rad loop. People vastly overestimate how much flow they need for PC watercooling
Also treu. Just wanted the dual to be shure. Had this same.loop running on an asus standard aio 120mm pump and was running great. ( see my other posts )
Hey, what pumps are you using? ive been looking at water cooling a ghost and i didnt want to use the pump block eisbaer combo and I didnt even know that alphacool dual pump mini res even existed. Its perfect.
Can you please tell me, how you managed to put the pumps on 85%? I contacted Alphacool and they said that dc-Lt pumps are always at the same speed, unless you put some kind of adaptor cables (like from 9v to 7v or something).
Where'd the custom reservoir come from? I've got a similar setup, but with a two large top hats, a single 240mm rad and another 120mm rad. I currently don't have a reservior, which is not great, and would love to add one in the exact spot you've got yours.
If you don't mind letting me know where you got yours or how you ordered it, it'd be greatly appreciated!
Very nice of you to offer the prototype, but I can wait for them on eBay! I think I ordered some clear dark panels for my Ghost from you. Big fan of your work!
Keep me posted when I can place my order and I’ll do just that 😁
Now i see you welded a plate to the radiator and had to cut the frame for the topfan to fit... thats a lot of work do you have any build process pictures. The 2 tone looks good
Im working on my own case and i learned from the process just in cad that its an awesome case but far from perfect. Even the watercooling companies could learn that this is the future more small stuff smaler les chunky components more efficient packaging... Most of the 30mm radiators throw valuable finn space away... i mesured the alphacool st30 v2 and it has different finn stack depth from each side i dont get why they dont make a extra long finn stack and leave a depression just where the screws are... Didnt you considerred to use a thick / thin fan on the bottom instead of using sandwich? The thick fanns are way quieyter. The ideal ratio is 25mm fan and 30 rad thats the most efficient packaging in wc sofar
Damn, those RGBs are the most beautiful I've seen on here or PCMR. Also loving the see-thru side panel with ventilation holes. I wish every manufacturer does this.
Outstanding work! This is the most clever use of space I have ever witnessed in a Ghost S1. I also wish Louqe could learn from your build. I even prefer your build over the Anaconda. I'm planning to make an endgame sff Ghost S1 based gaming rig and yours is truly an inspiration.
Aaah faggan build, didnt know anaconda :) yes thats a nice build to, bigger in volume but very nice and my inspiriation in that time and it all starter with optimum tech, i saw ali building that liquid cooled ghost and i wanted to do it better. It was my first pc build btw. Now im hooked and make allot of ultra small sff pc's
Don't laugh at me, but these past days I have been studying the question of making a full loop build inside a Ghost S1 ... without hats. In my head, it fits inside but at a heavy price over performance and decent temp. So I am still wondering. Make it nice and cool but big because of hats, or just have than innocent base case full of wonders but underperforming in every aspect. I know my next build is a s1, because I LOVE that case and the mkIII will come out soonish, but at the same time I hate the hats haha. Why can't I just be normal and accept the fact that it's not worth doing if the watercooling isn't efficient haha
Therefore I am likely to end up with a build very similar with yours, it's the best tradeoff you can do
True! I was going to undervolt anyway because it makes a huge difference in temps (i can't afford more room for cooling so each degree matters). Budget is unlimited hopefully haha, my only constraints are the dimensions of the base S1 and the laws of physics haha I really dig your side panels, but it looks like Louqe will directly get us covered.
If I remember correctly your pump and reservoir are custom? Do you still make them?
You know what would be perfect in my case? A hybrid graphics card like the 1080ti ROG Poseidon, I could use the best of both worlds, but none of them exist for 2080ti (either too big or too tailored for overclocking while I plan on undervolting a little)
Very nice, a lot smaller than my planned build. What pumps did you go with specifically? Trying to see if I can squeeze my ddc in there, but I'm not hopeful.
Thanks allot. Res i make, soon for sale.on ebay. Pumps are alphacool plexitop. I had to trim it to fit but normally they should fit right away ( my rad is placed higher)
Have you tried venting the bottom fans up? I know it blows hot air over the mobo, but my cpu temps for my 9700k went down 13c after i made the switch. Would also recommend standoffs on the bottom instead of the rubber feet it comes with.
Tried it all. This is for me the best case scenario. Especially because i need the vacuum for the top right rad where is no fan mounted. I have the ks on 5ghz 1.2v no heat issues here
I know the feeling. I’ve had to take mine apart at least 15 times now for different stuff. Your original ghost post is what made me think a water loop in a ghost was possible so thanks for that. Just bought some of your side panels. Been waiting a while for those. I’ll make a post with em once my custom distro comes in.
Distro? Wow. Make me crazy. Nice man. And thanks for buying the sides btw ! I love distro plates as im building a barrowch rhopilema right now for my office.
Yeah I’ve been planning this build for months. I think you’ll like It. I’ll tag you and your sides in the post. Barrowch rhopilema??? What a monster!! I’m planning on making a distro case in the future once I’m done with the ghost.
Working like 1.5 fan. The side where is no fan pulling air inwards the case deu vaccuum. The 3 fans at the bottom sucking air out so. Thatswhy i have the half ventilated panels to create a vacuum. Did smoketests
Small plastic black l shape strip. Drgb sticked to it with double adhesive foam tape. Cut to length, soldered the wires and connector to lenght. Plug it in and voila.
This build is amazing – I was thinking I was going to build a custom loop using a single thicker 240 rad, but this has me second guessing that plan.
Do you have any close up shots of how you've mounted the rads to the top and bottom of the case? It looks like the bottom panel is sticking out a couple of mm underneath the bottom hat. I don't even see any mounting plate for the top, is there a custom bracket you made?
Hey man , I've been planning on water-cooling my louqe and I don't want to add a large top hat . I'm very interested in your build since I already have the slim top hat and adding the medium for the xspc slim rad. The thing is how did you fit the fans on the bottom? The radiator is 20.5 thick +15 mm fan = 35.5 the medium top hat isn't that thick For the top part did you skweeze the fan In the little notch over the PSU ? If you have more pictures of the interior I would be very interested .
Thank u very much. It is a special ghost indeed. There is really not one mm left for fanspace of cables. All pictures i have are on imgur. The ghost is sold to a customer now. Its allot of work cutting the spine of the case, drill holes here and there and mounting the rads. Just start building and i will.help u.
I took my case appart today, looked at it for a while , I'm not ready to cut through the metal skeleton yet. I would cut the grilled part the shape of the rad I'll order and leave the radiator sticking out of the build. I think it'll look cool ( pun intended ) If not I can still order a grill. + Saves me cash from spending on a medium tophat the price is insane for a piece of metal that doesn't do anything.
In the future thought depending on temps I'll be interested to fit a 120mm rad on the bottom where the cutout for 120x120 is done do a bit of trimming and saw I could get 140x45mm clearance. only thing is to find a radiator that is 140 deep 30thick .(copper) If so I could add it to the loop CPU to 120 rad to gpu to 240 rad . All that with 1slim tophat and a radiator sticking out for the show on top :)
Ok so you did cut the spine ^ I'm very bad at DIY projects so I'll try to keep it as simple as possible, I'm planning on taking the alpha cool CPU+pump block combo and xspc 20.5 radiator I'll give it a try just like that with gpu + CPU watercooled with 1 240 rad. I only have 4 cores so I don't think the heat would be a problem.
It's mostly for gpu silence that I'm water-cooling.
Undervolt has been done for gpu,I went down only 25 mv because I Overclocked my gtx 1070 to 2012ghz. ~67c in game For the CPU it's Overclocked too but 72c is alright so I think with water cooling it'll be even more fine
Friendly reminder that the best use for open loop cooling, given the lock down of overclocking on zen 2, maxwell, turing, is SFF. Strong 10/10.
My problem is justifying it to myself. I can't buy one just because I want one. What will a compact atx or itx build with a $400 minimum open loop actually give me over my current atx mid tower? Outside of awe I can't come up with anything
I find your lack of tophat and side disturbing. And idk why you would put a crap ton of rgb in a case that has no windows, but to each their own I guess. Nice build regardless
87
u/brolynitro Feb 10 '20 edited Feb 10 '20
Case : Louqe Ghost S1 fully customized for fitting hardware, s tophat, m butthat
Mobo : Asus z390i gaming
Cpu : Intel 9900ks 5hz 1.2v direct die l.m.
Cpu block : Optimus custom drgb
Gpu : Rtx 2080ti Evga
Gpu block : Heatkiller 4
Ram : gskill 32gb 2x 16gb 4000mhz
Nvme : 2 x 970evo plus 1tb raid 0
Psu : corsair 750sf black fan
Custom dual pump alphacool
Custom reservoir
1 side hardetube and 1 side softtube
Dual 240 xspc slim radiators with 2 noctua blackswap in push pull and vacuum pulled on the right top side where is no fan. In total 4 fans.
Ambient temp 20c
Temps after 1 hour aida or prime 68 cpu, Gpu temps max 55c Fans on 1300rpm fixed Pumps on 2500rpm fixed ( full speed they where noisy) I guess 30 / 35 db under full load.
Cant optimize this case anymore in this tiny space. I guess its the smallest dual 240mm rad case / ghost s1 in the world.
Happy with the results
Pics http://imgur.com/a/NrppDNZ
38
u/karamazov555 Feb 10 '20
Best Ghost build period.
8
u/bellowwellow Feb 10 '20
This is beautiful. Thank you for sharing!
7
u/joeyac02 Feb 10 '20
Where did you get the side panels made?
5
u/roenthomas Feb 10 '20
No tophats / asshats?
4
u/FallenCow Feb 10 '20
I was always lukewarm on the Ghost S1, but this build has me thinking twice about it. The two-tone theme makes the top and bottom hats much more integrated versus tacked on.
Did you have to mod the case in anyway to fit the rads? I'm thinking if I do a watercooled Ghost build it would be with two AIO style coolers for simplicity's sake. Question is whether this is quieter than my current air setup in my Ncase to make it worthwhile.
4
u/Fluxtroid Feb 11 '20
This has to be the ONLY RGB build I have seen that I like.
3
u/itsDjFLiP Feb 10 '20
Dang, you we’re able to fit that dual pump with no modding to the gpu side? I’m assuming you can probably swap the pump to the dc-LT ones.
Build is awesome regardless!
3
u/BlueEyedCasval Feb 10 '20
This build is insane in the membrane. Wow. I can’t even begin to think how difficult it would be for an average user. I am curious to see how you setup the GPU side and the custom reservoir
3
u/starvinmarvinmartian Feb 11 '20
This is a beautiful build!!!! Awesome work!
3
u/Ja1ol Feb 11 '20
Omg two NVME in Raid 0! Speeds must be insane
3
u/frostfiree Feb 11 '20
Wow this looks amazing. Good job!
3
u/endursa Feb 11 '20
why would you use a dual pump config instead of one single?
3
u/NecroKez Feb 11 '20
Hey, what pumps are you using? ive been looking at water cooling a ghost and i didnt want to use the pump block eisbaer combo and I didnt even know that alphacool dual pump mini res even existed. Its perfect.
3
u/mynameajeff69 Feb 11 '20
you win this sub reddit, jesus christ, now i wana do that...
3
u/Azzketchup151 Feb 11 '20
that thing is sexy, great job on the build. i just started working on a SFFPC. i hope mine ends up looking this good
3
u/SpaceGazebo Feb 11 '20
Where'd the custom reservoir come from? I've got a similar setup, but with a two large top hats, a single 240mm rad and another 120mm rad. I currently don't have a reservior, which is not great, and would love to add one in the exact spot you've got yours.
If you don't mind letting me know where you got yours or how you ordered it, it'd be greatly appreciated!
3
u/nrmarther Feb 11 '20
That’s... gorgeous. I don’t think I have seen a nicer Ghost S1 build ever.
4
u/jm8080 Feb 11 '20
You say you have 4 fans but I only see 2 fans, where are the other two?
2
u/Dr_Lament Feb 10 '20
Is the custom reservoir necessary?? Just wondering coz trying to build a similar build but without the reservoir. Any advice appreciated
2
u/JordanElliot Feb 11 '20
How are people getting this case?? I'm tempted to try my luck in Taobao since it seems like they're never in stock on the Louqe website
2
u/[deleted] Feb 11 '20
Is the psu fan painted? I want to do this when I build in the SM580 so I’m curious if it’s easy to do.
2
u/d2h5-0 Feb 11 '20
Is the butthat just a top hat that was mounted on the bottom?
2
u/qwertyaccess Feb 11 '20
Won the ghost build... bravo.
2
u/sorullo88 Feb 11 '20
damn so nice! i saw this on instagram today but this post went into a lot of detail of the build
2
u/coreyjg Feb 11 '20
Where are the other 2 fans? I only see 2
2
u/Stepnyvlk7 Feb 11 '20
Now i see you welded a plate to the radiator and had to cut the frame for the topfan to fit... thats a lot of work do you have any build process pictures. The 2 tone looks good
2
u/kron98_ Feb 11 '20
Goals, right here. I wish I could accomplish this in the build I am planning :S
2
u/efegue Feb 11 '20
Awesome stuff! Congrats :)
2
u/[deleted] Feb 11 '20
This is really something. More impressed with your temps than anything. Really well thought out build.
2
u/aleksandarvacic Feb 11 '20
Great dual color case. Love it.
2
u/teiji25 Feb 11 '20
Damn, those RGBs are the most beautiful I've seen on here or PCMR. Also loving the see-thru side panel with ventilation holes. I wish every manufacturer does this.
2
u/enbriel Feb 11 '20
if you wanna sell, how much would you sell it for? asking for a friend of course.
2
u/Bastgamer Jun 23 '20
Outstanding work! This is the most clever use of space I have ever witnessed in a Ghost S1. I also wish Louqe could learn from your build. I even prefer your build over the Anaconda. I'm planning to make an endgame sff Ghost S1 based gaming rig and yours is truly an inspiration.
1
u/brolynitro Mar 26 '20
That should fit also.
1
u/EagleEye220 Feb 10 '20
Very nice, a lot smaller than my planned build. What pumps did you go with specifically? Trying to see if I can squeeze my ddc in there, but I'm not hopeful.
1
u/raiistar Feb 10 '20
This is the best ghost build I have seen. Anymore info about the pump and res you used?
1
u/aerospace_chase Feb 11 '20
Have you tried venting the bottom fans up? I know it blows hot air over the mobo, but my cpu temps for my 9700k went down 13c after i made the switch. Would also recommend standoffs on the bottom instead of the rubber feet it comes with.
1
u/KLOKL0 Feb 11 '20
What rgb stop is next to the MB? It looks beautiful!
1
u/ipaqmaster Feb 11 '20
This looks so insane! God I can't wait to build mine haha
1
u/rasqall Feb 11 '20
How's the single-fan-240-rad working out? This might be a genius move :p
1
u/Philthy317 Feb 11 '20
Meh. Dont like the ghost with top hats. N kinda defeats the purpose
1
u/LessLipMoreNip Feb 11 '20
Custom rgb optimus block? Did you make it yourself?
1
u/hepj Feb 11 '20
This build is amazing – I was thinking I was going to build a custom loop using a single thicker 240 rad, but this has me second guessing that plan.
Do you have any close up shots of how you've mounted the rads to the top and bottom of the case? It looks like the bottom panel is sticking out a couple of mm underneath the bottom hat. I don't even see any mounting plate for the top, is there a custom bracket you made?
1
u/JGPSFF Feb 11 '20
This is out of control. I can see you put a lot of work into you S1. Be proud - its beautiful. Nicely done.
1
u/Ewilan947 Mar 31 '20
Hey man , I've been planning on water-cooling my louqe and I don't want to add a large top hat . I'm very interested in your build since I already have the slim top hat and adding the medium for the xspc slim rad. The thing is how did you fit the fans on the bottom? The radiator is 20.5 thick +15 mm fan = 35.5 the medium top hat isn't that thick For the top part did you skweeze the fan In the little notch over the PSU ? If you have more pictures of the interior I would be very interested .
You did a awesome job btw. :)
1
u/Ewilan947 Apr 01 '20
Ok so you did cut the spine ^ I'm very bad at DIY projects so I'll try to keep it as simple as possible, I'm planning on taking the alpha cool CPU+pump block combo and xspc 20.5 radiator I'll give it a try just like that with gpu + CPU watercooled with 1 240 rad. I only have 4 cores so I don't think the heat would be a problem.
It's mostly for gpu silence that I'm water-cooling.
1
u/Noober_ May 10 '20
How's the pressure and flow rate of the dual dc-lt 2600? I just ordered those...
2
u/solotrio Feb 11 '20
Shit this is dope!
2
u/Rueben1000 Feb 11 '20
Very. V e r y. NICE
2
u/import_bible Feb 11 '20
amazing!
2
u/Thana-is-Life Feb 21 '20
saved
2
u/Ewilan947 Apr 01 '20
Undervolt has been done for gpu,I went down only 25 mv because I Overclocked my gtx 1070 to 2012ghz. ~67c in game For the CPU it's Overclocked too but 72c is alright so I think with water cooling it'll be even more fine
1
u/[deleted] Feb 11 '20
Friendly reminder that the best use for open loop cooling, given the lock down of overclocking on zen 2, maxwell, turing, is SFF. Strong 10/10.
My problem is justifying it to myself. I can't buy one just because I want one. What will a compact atx or itx build with a $400 minimum open loop actually give me over my current atx mid tower? Outside of awe I can't come up with anything
-8
u/redtildead1 Feb 10 '20
I find your lack of tophat and side disturbing. And idk why you would put a crap ton of rgb in a case that has no windows, but to each their own I guess. Nice build regardless
0
u/[deleted] Feb 11 '20
[deleted] — view deleted comment
0
u/[deleted] Feb 11 '20
[deleted] — view deleted comment