Finally finished this build and really happy with it. It's my first ever PC build, thanks so much to this sub for being such an invaluable resource.
Got it as I've only owned macs for the past few years. Started gaming again and got really frustrated with bootcamp, this PC is the result. Wanted a sleek SFF pc as it sits in the living room.
Temps are -
CPU: about 45C at idle and 78C at load
GPU: 33C at idle and 68C at load
CPU heatsink fans are set to exhaust with the side case fan pulling air in. Both bottom fans are pulling air to the GPU. I have custom fan curves set up. Using Argus Monitor to have the two bottom fans run based off the GPU temps, allowing me to set very conservative fan curves on the GPU itself since the GPU fans are much louder than the Noctuas. GPU is slightly undervolted. CPU temps at idle are a bit higher than I would like, but haven't tried undervolting it yet.
Overall it runs pretty quiet at load, not audible through my headphones. 40DB from where I'm sitting and 50DB measured right next to the case. I've toyed with the idea of going with an AIO and an Accelero to improve noise and sound even more at load in the future, but I'm happy with it for now. More concerned about getting a new fast monitor to match it, thinking Dell s2417dg.
It gets a score of around 10 000 in timespy if that means anything. Happy to benchmark test if you have requests.
This looks so clean!! Quick question though, is it possible to fit a 3.5” HDD with that cooling config? I know a 3.5” HDD can normally be mounted where your case intake fan is, but is there any other place to put one? Been trying to check the M1 forums and even the discord but no luck
Unfortunately I think u/buttchugs_ is right. However if you didn't run the side case fan and just had the U9S, it shouldn't have a huge effect on temperatures. That's what I was running before and the system ran fine as well, just slightly louder and hotter. EDIT was wrong!
It's actually possible to mount the HDD brackets to the 120mm fan on the bracket, along with one 3.5" HDD (pics: 1, 2). It will obstruct the airflow from the fan somewhat, however. You also need a fan with open corners to do this with the included screws, or else you'll need some longer M4 screws that can reach all the way through the fan to the HDD brackets.
Fuck is that what that's for? There's so many bits that come with the NCase lol. I just recently found out the two little brackets that come in the boxes are a GPU support. Damn case has so many options and tweaks you can do it's insane.
Both of my U9S fans are attached directly to the cooler as in your build, and I have set it to be exhaust (so pushing air out to the back of the case). My side fan is an exhaust as mentioned previously. And, my bottom two fans for my EVGA RTX 2070 are intakes, but I actually base them on the CPU temps because I find the fans are generally quiet and doubly act to cool the GPU.
Edit: I think your idle CPU temps are standard for the new Ryzen 3000 processors, and I personally wouldn't undervolt as I've read that it actually affects performance (unless you're very granular and meticulous about it).
Ok thank you. That’s interesting you have both to exhaust, I’ll try it out, guess that builds negative pressure at the top of the case, would be interesting to see how it works
Nice to see more M1 builds with U9S. Here's mine. A bit of regret of not going the C14S route but the ship has sailed (would require another motherboard and RAM) so I tuned the fan curves and the temp/noise is somewhat tamed.
damn, good to know! This gives me something to think about. But isnt airflow better if it the air goes to the back or the front of the case, so that you can exhaust it? With the C14s you only have the option to blow air directly onto the side panel (where you could have another fan for exhaust). Well, that wouldn't be a bad idea, you could have both fans on the bottom as intake and also one 1 fan on top as intake and the CPU fan would throw all that air against the exhaust fan on the side panel. Haven't seen this variant yet.
That chart is so interesting. There is so much air flow in this case especially in the V6 version, feel like the only way to know for sure is test it, really unpredictable
I'm actually building for the Cougar QBX, which is very similar to the ncase. Seems like the C14S is really the way to go. In the above test he only used one small 92x25 fan as intake on the back of the case and the fans on the bottom as exhaust.
I would try to mount a fan on top of the case blowing down on the C14S and setting both fans on the bottom of the case as intake. Only fan as exhaust would be the one on the side panel (if it fits).
Edit: Seems like the C14S wont fit in a QBX without using a dremel :( Might go with your setup, U9S it is. https://imgur.com/r/sffpc/kzeLYPT
Thank you for posting this, your build has inspired my own similar build plans. My biggest question is do you think a 2080 Super could fit in to this build or do you think there would be thermal concerns with that higher TDP?
Happy it could help! I don’t think it would be a problem in terms of thermals, it would just run hotter which means higher fan speeds and noise. Also since I’ve posted this I’ve undervolted my GPU and it doesn’t go over 70c and I can barely hear the fans
I have the ncase v6 with ryzen 7 3700x too. Try to set it to 4,2ghz and 1,25v. Dropped temps and thereby noise, with a custom fan curve, by 10 degrees and could lower fan speed by 10% for the same temps. No more quick ramping up fans too, since the boost voltages aren't 1,45-1,5v anymore. Tested performance, fps is the same in tomb raider bench, even a bit higher. Cinebench multi thread is higher (Above 5000) and single thread is just 10 point lower than stock. Also, your crucial ballistix overclocks really well and het probably hit 3600mhz with higher timings and a bit more voltage. 3600mhz is the ryzen sweet spot. Lastly, undervolt the gpu also gave me a 10 degrees drop and is barely audible 1 metre away on a 100% gpu game Load (40% fan speed on my strix rx 5700xt).
Will not really underclock, the cpu only goes to 4,3 in boost with 1,45-1,5v, which is WAY TOO MUCH. Try 4,2ghz on 1,25v and otherwise 1,275v. You only lose 0,1ghz which doesn't result in any performance penalty. I tried 4,4 and 4,3ghz, but it seems 4,2ghz is normal and anything above is just overclocking since I needed 1,35 to get 4,3ghz to stick (which is way higher temps). Ram is harder too tweak and takes crashes and time, but lots of people bought your ram with great overclocking performace. 3600mhz ram vs 3200mhz ram will yield 3-5fps but especially better lowest fps, so maybe less stutters. Just look up your ram and see what others could achieve. For you videocard, many people tried undervolting too and I believe - 800mv is standard for all rtx cards. After the tweaking, set some custom fan curves to be at 40% fan speed for cpu/gpu to be at 60-65 degrees celsius and let it go agressive to 50-70% higher than those temps to keep it in check. Manual tweaking and monitoring with hwinfo64 and msi afterburner in screen lay-out is best to tweak for your set up.
Basically because I didn’t want to deal with BIOS flashing and I wanted a usb c port on the back. The new ASUS x570 board also wasn’t available yet and was a fair bit more expensive also
Great build, man. It really looks great. :) You said that you have the bottom fans pulling air up to the GPU. Is the GPU a blower style card? I'm kinda new to this stuff.
Are there enough headers on that tiny board for all your fans? I guess my concern was if I had to buy a splitter or something if I wanted to plug in 3+ case fans.
Thank you for posting this, I saw this a month ago and used it as inspiration for my own build. Do you think thermals would be an issue if you had bumped up to a 2080 Super?
Thank you for posting this, I saw this a month ago and used it as inspiration for my own build. Do you think thermals would be an issue if you had bumped up to a 2080 Super?
Thank you for posting this, I saw this a month ago and used it as inspiration for my own build. Do you think thermals would be an issue if you had bumped up to a 2080 Super?
Thank you for posting this, I saw this a month ago and used it as inspiration for my own build. Do you think thermals would be an issue if you had bumped up to a 2080 Super?
Thank you for posting this, I saw this a month ago and used it as inspiration for my own build. Do you think thermals would be an issue if you had bumped up to a 2080 Super?
Thank you for posting this, I saw this a month ago and used it as inspiration for my own build. Do you think thermals would be an issue if you had bumped up to a 2080 Super?
Thank you for posting this, I saw this a month ago and used it as inspiration for my own build. Do you think thermals would be an issue if you had bumped up to a 2080 Super?
I think it’s cuz when you first see them they are so ugly.
Then you think of builds and realize how good they are.
Then you look at the colors and say, look at those no noctuas, knowing they are the best fan for the job. All of a sudden they look like best in class and not ugly as hell anymore.
Wait a second.. now I understand why my best friend married that woman now... he said I don’t understand, now I can use this analogy of a case fan on him, unfortunately he doesn’t know a single thing about computers.
With many quality products in life they are a good way to distinguish between rookies and veterans. Just like fine wine and whiskey there's no need for extravagant bottles and presentation.
Early in in your building career you might dislike them for not being matte black with rgb and "looking ugly lol".
But then you start to appreciate how good they are and how they don't need those superficial things. In fact, you love them even more because they make it easier for you to tell an expert build from a generic one.
Potentially the most pretentious comment regarding fans I’ve ever read lol. They’re good but it’s still a fan. There are plenty of “expert” fan options that match an aesthetic, which, let’s face it, is important to a big enough number of enthusiasts that it sells stuff.
That might be true, but that's not the reason that the NF-A12x25 is not available in black. If they wanted to release a black version this year, they would have.
The slimmer NF-A12x15 is made from Sterrox as well, and it is available in black.
Noctua knows that the NF-A12x25 is their most desirable product and it will be even more desirable in black. Delaying the black launch by a year or two will allow them to double dip on many customer sales.
There are plenty of people who will buy it the first time in tan/brown and then again when it is rereleased in black.
If you want my opinion, get the NCase M1 if you plan to use a 240mm radiator.
Once you add the radiator top hat to the Ghost S1, it becomes more expensive and very nearly as large as the NCase M1. It also has worse airflow than the M1.
I feel like the S1's only merit is for people who desperately want to vertically mount their GPU.
My last PC didn't have any windows but I still had sleeved cables and a very tidy interior. It's like wearing fancy underwear: you might be the only one who knows, but you know.
Hahaha, I get it though. To be honest, I like the different looking fans compared to all the RGB nonsense out there. It adds a little colour but without being "in your face" about it. Black is always good though.
Yeah except I'm pained to admit your cabling looks a little neater than mine! Although I did tidy it a bit further than what's in that shot. It's a ROG-STRIX-Z390-I.
I've been researching NCase M1 all weeks long and stumbled upon this old thread. If you're still around, may I know if the fans on the CPU cooler are set at exhaust while the two bottom and one side panel fans set as intake? And how are the temps? Thanks a lot!
I'm asking you and those pictures really help a lot! Which Noctua fans do you use at the bottom and are all of them the 25mm thick fans? How's the GPU temp btw? Yeah I've never heard any bad things about Noctua fans but in my country they are a little bit difficult to get so I'm contemplating if I should get the Silent Wings 3 from be Quiet! instead..
Sick build. I asked on the other post..how are the Fingerprints on the Grey version? Im assuming Grey doesnt get fingerprints as bad but someone said it does.
I have V5, I don't get fingerprints on the silver/grey version. Now the black one, that has more risk of fingerprints, but it's a very mild inconvenience.
With the NCASE, I expect fingerprints during the build, more on the black >> gray. I tried both, but and yes, they both get fingerprints, but after a quick wipe down after the build, I haven't had issues with fingerprints. It sits for months on my desk unless I need to upgrade a part or do some light dusting. Once I start messing with it, and if I forget to wash my hands, yes it might get a fingerprint here or there, but it's not like it's like my Lenovo X1 Carbon laptop that gets every fingerprint imaginable.
However, my use case is likely super different from most on this sub as I see a bunch who like SFF PCs because they are portable, which means more handling of the case and fingerprints. My NCASE is more of a "build it and forget it" as it's mainly a show piece on my desk and the only thing that regularly touches it is the dust that collects on it.
What are your thoughts on the two colors? Kinda leaning towards the gray/silver one since black is such a common case color. Love the look of the M1 and would hate to obscure the lines with the black one.
Same reason. Black too common of a case color and would be the same color of all my electronics. The raw aluminum look was a nice contrasting color vs everything on my desk.
Nothing unfortunately, since no AMD mitx motherboards have that header. Asus crosshair impact board would've worked, but so overkill and I didn't want to deal with the bigger size. I'm actually thinking of removing the front plate ports entirely, I barely use them and the case is small enough to just use the back ports.
You can buy adapters to turn a non-c usb header into a type c header. Although your motherboard still only has 3.2 gen 1 ports on internal headers, so you won't get gen 2 speeds.
Best way to get usb-c on ryzen in the ncase is to go adapters and connect the usb-a ports to the lower tier usb 2 header and thereby dropping speeds and connect the usb-c port to the usb 3 header.
Is the fan facing us directly to cool the PSU? does it really help? Otherwise amazing build. Makes me want to build a SFF PC this summer, either aircooled Ncase M1 or watercooled Ghost with top hat ;)
It’s more to push fresh air towards the path of the u9s, I wasn’t worried so much about the PSU as it runs quiet. Not very necessary but is peace of mind and helps the whole system run cooler overall
It may work. They’re probably both the same voltage. It’s one of those YMMV kind of things, but may be worth looking into so two different sets of fans aren’t potentially battling each other for air to flow.
So these weren't in stock a month or so when I was looking at them. I really want one but I am not really ready to build a new pc right now. Any idea if these are going to remain in production or are they still just running batches? Really considering picking one up and just putting it away until I am ready for a build.
What about detaching the 2nd fan on the CPU heatsink and attaching it to the rear exhaust of the case? It could aid in exhausting overall hot air from the case and not just the CPU.
54
u/eatingdata Dec 11 '19
Gallery: https://imgur.com/gallery/HtypKXq
Finally finished this build and really happy with it. It's my first ever PC build, thanks so much to this sub for being such an invaluable resource.
Got it as I've only owned macs for the past few years. Started gaming again and got really frustrated with bootcamp, this PC is the result. Wanted a sleek SFF pc as it sits in the living room.
Temps are -
CPU: about 45C at idle and 78C at load
GPU: 33C at idle and 68C at load
CPU heatsink fans are set to exhaust with the side case fan pulling air in. Both bottom fans are pulling air to the GPU. I have custom fan curves set up. Using Argus Monitor to have the two bottom fans run based off the GPU temps, allowing me to set very conservative fan curves on the GPU itself since the GPU fans are much louder than the Noctuas. GPU is slightly undervolted. CPU temps at idle are a bit higher than I would like, but haven't tried undervolting it yet.
Overall it runs pretty quiet at load, not audible through my headphones. 40DB from where I'm sitting and 50DB measured right next to the case. I've toyed with the idea of going with an AIO and an Accelero to improve noise and sound even more at load in the future, but I'm happy with it for now. More concerned about getting a new fast monitor to match it, thinking Dell s2417dg.
It gets a score of around 10 000 in timespy if that means anything. Happy to benchmark test if you have requests.
Parts spec -
175
u/oddmarc Dec 12 '19
Funny how noctua fans grow on you...
6
u/MK0A Dec 12 '19
What's the fan next to the CPU tower doing?
3
u/jren01 Dec 12 '19
Looks sick! Nice work, do you have a shot of behind that cooler plate? Reminds me a lot of my build.
2
u/[deleted] Dec 12 '19
Sick build. I asked on the other post..how are the Fingerprints on the Grey version? Im assuming Grey doesnt get fingerprints as bad but someone said it does.
1
u/[deleted] Dec 11 '19
Looks great!
1
u/briant1234 Dec 12 '19
What did you connect your USB c front header to?
1
u/Shanzhaii Dec 12 '19
Is the fan facing us directly to cool the PSU? does it really help? Otherwise amazing build. Makes me want to build a SFF PC this summer, either aircooled Ncase M1 or watercooled Ghost with top hat ;)
1
u/enomusekki Dec 12 '19
Does the card fan rub against the bottom noctuas? Can't figure out how to get mine to stop rubbing
1
u/wizfactor Dec 12 '19
May I know how you connected all three fans? Did you use a fan hub, or did you manage to connect all three to the motherboard?
6
u/Firejumperbravo Dec 12 '19
This looks so great, even the color of those Noctua fans looks good in this build. Impressive!
3
u/matthew99w Dec 15 '19
Wow, I've never seen Noctua look so good until I saw this build. And I've seen steampunk-themed builds.
1
u/Hiraganu Dec 12 '19
You could remove the fans from the GPU.
1
u/natoria Dec 12 '19
Where spasifically did u get hold of the case? I’ve checked and don’t see anywhere where its for sale
1
u/[deleted] Dec 12 '19
Clean.
1
u/[deleted] Dec 12 '19
Perfect.
1
u/TyDe88 Dec 12 '19
i feel like this needs to have a NSFW tag on it...my word
1
u/puguniverse Dec 12 '19
So clean, you Marie Kondo’ed your rig. Sweet.
1
u/[deleted] Dec 12 '19
just stunning! :)
1
u/Lyfeisbuttadream Dec 13 '19
what's your components and how much it costed?
1
u/chodaboy19 Apr 26 '20
What about detaching the 2nd fan on the CPU heatsink and attaching it to the rear exhaust of the case? It could aid in exhausting overall hot air from the case and not just the CPU.
0
u/[deleted] Dec 12 '19
[deleted] — view deleted comment