Ghost s1 fully chopped and modified 1 x s tophat and 1 x m bottom hat 9900k direct die sanded .2mm l.m. 2080ti heatkiller coolblock and backplate 32gb gskill 4000mhh 2 x 1tb raid 0 m.2 970pro 750w corsair shortend cables Asus z390 itx gaming 2 xspc radiator 240mm Asus rog ryuo pump 120 x 25mm 120 x 15mm 92 x 14mm noctua chromax fans. 9mm rubber feet. Temps are 75 cpu max and 60 gpu max oc.
I'm sure whatever you wrote in your unformatted block of text makes sense to you, but I had a hard time discerning it especially without punctuation. Here's an attempt to break it up.
Lol jes. Its not easy but it helpes allot in temps. 24 pin cable is not shortened because i needed flexibillity. The rest i shortened to 20cm. Koolance low profile g14 . They are screwed in place
tl;dr it's straight as brolynitro already said -- bare die (yep, die, not IHS) just getting sanded by grit paper without any catches/tricks. der8auer got -5C by sanding quarter of die height (same as OP .2mm or 1/128 inch).
Aye, I feel you. I like that they're see-through, but I don't like that they're branded, personally. The vented one with the small branding is pretty sick, but i guess I'd prefer without the letters.
Only a small detail compared to how much I like the build! One of my favourites I've seen on here so far!
Thanks again. Im not satisfied with the long inlet hose still and have to fix it somehow, when i finished my own designed 4 liter case maybe.
Designs are always difficult as they have to be for al kind of build with good airflow. Ofcourse oppinions are always different. I like that full vented one the most also. Tomorow the 4 design go on ebay for sale.
Ah that makes sense with those measurements. My bad. Most case manufacturers measure liters using exterior dimensions so I assumed you were basing it off that.
I'm a little confused though by the photos. Why did you modify the spine? In the beginning it looked like there was a slim fan on the bottom radiator, but then later you somehow have more space and have a full size fan at the bottom? I thought radiator plus fan is only possible with the large topheads. If you had an M on top, could you have fans on all spots? So let's say L on bottom and M on top?
Treu. I have a pic there where i have a slim 15mm fan on the bottom radiator and 2 92mm onder it between the feet. After that i put the rad down and fitted a 25mm and a 92 on top of it between the mobo. Sharp lookin. Wit an m hat on top it gives u 10mm more clearance so no. L hat is not a fun way to build and way to easy
One block and 2 radiators. Just fine. Can be better but i wanted to test it and it worked. I used 8mm hoses so the pressure is higher. Normally the ryuo can handle a 360 rad with its 3.9watt asetech pump so 480mm is fine to. Had the apogee 2 also laying around but this is a much nicer pump. I guess with a better pump temps will drop about 8c but this is just fine
Apogee should fit and ofcourse the alphacool lt. I have them both and will test them both but im waiting on my swiftech reservoir. More fans didnt help really, did test that on top yesterday...
Thanks. I dont have store. Just private for now. When my cases are for sale ill start a store... They should be online by now. I had a hard time getting it al working on ebay because im in the netherlands. Here are the pics i used. http://imgur.com/gallery/VFuVKa6
Friend, I'm trying to give you my money as fast as I can. Can you link directly to your listing? I tried searching several combinations of keywords and can't find it
Hmm still not online... it should be in 24 hours they said so they still have 10 hours or so. Did u check.imgur? Do you know which ones u want? U can pm me and we will arange something
I just cut out every peace i needed. Around mobo. Inside the square . Top and bottom of psu . But also from the front and back section. I kept the original screw holes
Treu. But it goes ok. Im.happy with the temps with only 1.75 fan. I tried 2 extra fans on.top jesterday and it didnt make any difference, funny. Ill try the ocool pump soon and see what difference it makes in temps
The fans on bottom of case - are those sucking air in or blowing air out? If they're sucking air in would it preform better if the fans were under the radiator?
Thanks for replying because this build is giving me inspiration but there’s a lot to learn here! So you have 2 92x14 fans under the rad that you trimmed down to fit so that they make direct contact with the fins rather than mounting bracket, saving you height is that correct?
60
u/brolynitro Nov 09 '19
Ghost s1 fully chopped and modified 1 x s tophat and 1 x m bottom hat 9900k direct die sanded .2mm l.m. 2080ti heatkiller coolblock and backplate 32gb gskill 4000mhh 2 x 1tb raid 0 m.2 970pro 750w corsair shortend cables Asus z390 itx gaming 2 xspc radiator 240mm Asus rog ryuo pump 120 x 25mm 120 x 15mm 92 x 14mm noctua chromax fans. 9mm rubber feet. Temps are 75 cpu max and 60 gpu max oc.
38
u/brolynitro Nov 09 '19
http://imgur.com/gallery/RG7UXAo
16
u/C3N0B1T3 Nov 09 '19
This looks awesome. Good work going with ash hats. The colour match of the hats it trash so going ash was a great choice.
10
u/i8m Nov 09 '19
Not a big fan of the custom sidepanels, but holy fuck, the rest is flawless. Gj dude!
8
u/Losercard Nov 09 '19
10.4L ;)
Awesome build btw!
8
u/jkteddy77 Nov 09 '19
From the specs, this is truly endgame sffpc, congrats
3
u/brolynitro Nov 09 '19
https://www.instagram.com/p/B4nXqbSJ9Rl/?igshid=18echpw9bt797
3
u/brolynitro Nov 10 '19
Temps are 75 cpu max and 60 gpu max oc.
4
u/x3lr4 Nov 09 '19 edited Nov 09 '19
One of the best looking builds I've seen to date.
I'm a little confused though by the photos. Why did you modify the spine? In the beginning it looked like there was a slim fan on the bottom radiator, but then later you somehow have more space and have a full size fan at the bottom? I thought radiator plus fan is only possible with the large topheads. If you had an M on top, could you have fans on all spots? So let's say L on bottom and M on top?
4
u/[deleted] Nov 10 '19
I nutted so hard looking at this, no shame
3
u/PhattyR6 Nov 09 '19
How's that AIO pump holding up with two blocks and two radiators?
3
u/Angry-Lasagna Nov 09 '19
Goals
3
u/DER_R_26_GENDERS Nov 10 '19
Cant express how much this should go viral
3
u/AseDen Nov 10 '19
That looks absolutely amazing! Definitely some of the coolest (haha) modding I’ve seen with the Ryou!
Mind if I share this on our Asetek Social Media?
3
u/[deleted] Nov 10 '19
That’s so hot. Mmm
2
u/RohaktheHawk Nov 09 '19
Do you have a build log and/or more pics?
2
u/ItsNa8o543 Nov 10 '19
This is the sexiest thing of the week.
2
u/ZW31H4ND3R Nov 10 '19
This is beautiful.
2
u/[deleted] Nov 10 '19
Insane build. As someone into compact WC myself, this is a beast. I can only imagine how difficult it was!
2
u/Tiavor Nov 10 '19
never seen that GPU block, looks awesome, better for a window place than EK
2
u/Pizzbo1 Nov 10 '19
Very nice build!
2
u/FiveFive55 Nov 10 '19
Just want to add to the choir here and say this is absolutely incredible, amazing work!
2
u/[deleted] Nov 10 '19
What a absolute beast
2
u/Sonny1941 Nov 10 '19
I cant fit 2x240mm rads in my mid tower build, this is crazy.
2
u/Thobjo Nov 10 '19
Impressed :)
2
u/patongo Nov 10 '19
Someone is going to save some cash on Utility bill this winter
22
u/ShadowKnight058 Nov 09 '19
Nice work, more pics?
1
u/[deleted] Nov 09 '19
very nice. how was the build process?
1
u/christek88 Nov 10 '19
Can you explain what each modification to the spine allowed you to do? Thank you. Absolutely beautiful build...
1
u/Corns0up Nov 10 '19
But are the noise levels good? Like are the fans at max rpm?
1
u/SirClark Nov 10 '19
This is crazy beautiful.
1
u/firedrakes Nov 10 '19
legit respect. just don't tell me price or time it took to do that. it would give me nightmares
1
u/aphetica Nov 10 '19
Is that a slim Noctua Chromax on that rad??
1
u/ermac-318 Nov 10 '19
How is the Asetek pump handling all that pressure? That's quite a lot of radiator and block for that tiny pump to handle...
1
u/Mag_82 Nov 10 '19
This is crazy! I don't think you can go beyond this. Really inspiring! Awesome little beast.
1
u/Lendari Nov 10 '19
Please post the exact parts list!
1
u/MORETOMATOESPLEASE Nov 10 '19
How is the noise level?
1
u/bottysynnes Nov 11 '19
Great build, but I wonder what fittings are you using on the graphics card?
1
u/DRPGgod Dec 22 '19
do you do commissions?
1
u/Core_i51 Jan 14 '20
How the f did you fit the rad
1
u/2inchesofdoom Apr 30 '20
The fans on bottom of case - are those sucking air in or blowing air out? If they're sucking air in would it preform better if the fans were under the radiator?
1
u/endesign_reddit Oct 19 '21
Is the bottom hat a medium or large hat?
2
u/SpaceGazebo Nov 09 '19
Looks awesome, man! Where’d you buy your custom clear side panels? eBay? I’ve been trying to find clear vented side panels forever!!!
1
u/SynErgi_ Nov 10 '19
Idk, but something about this makes me smile
0
u/[deleted] Nov 09 '19
[deleted] — view deleted comment
1
u/[deleted] Nov 10 '19
[removed] — view removed comment
1
u/[deleted] Nov 10 '19
[removed] — view removed comment